Where to Buy ATI | Analog Audio Distribution Amplifiers

Viewing Item(s):

Display

Show As

Rack Mount For ATI AV8 NanoAmp and MicroAmp
Item# 21075-501
Spare Amp Module Connector Assembly for DA/MDA/IDA/MIDA/CDA 100 with Barrier Block & Fanning Strip
Our Price: $105.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI ADA 206-XLR Dual 1x3 Low Noise Analog Audio Distribution Amplifier - XLR Connectors
Item# ATI-ADA-206-XLR
The DA206 is ideal for every application and every budget. Avoid RF and hum pick-up problems from noisy, lossy splitters. Prevent hard-to-find shorts from multiple taps on critical lines. Boost console outputs. Drive long lines. Eliminate rolloffs and distortion from mismatched load impedances and enjoy the maximum versatility that this unit provides. The DA206 gives you two inputs, each driving a master input gain adjustment and three individual output level trimmers. All outputs...
Our Price: $1,625.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI ADA 416-PHX Quad 1x4 Low Noise Analog Distribution Amplifier- Phoenix Connectors
Item# ATI-ADA-416-PHX
The ATI ADA416-PHX is an amplifier capable of routing audio to four distribution amplifier channels, all via balanced Phoenix inputs and outputs. The unit provides a master gain adjustment control for each channel, while individual trimmers are on hand for each output to accommodate gears of various sensitivities over its 20 dB range. Use it to distribute audio in offices, nightclubs, and more. You're sure to get a low-noise, strong-signal operation out of the unit, as it's RF protected...
Our Price: $2,185.00
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
ATI ADA412-XLR Quad 1x3 Low Noise Analog Distribution Amplifier - XLR Connectors
Item# ATI-ADA412-XLR
When you are searching for a solution to extensive audio problems, the ATI ADA412 can handle any issue you throw its way with strength and reliability. The ADA412 is RF protected and eliminates noise from lossy splitters while driving long lines. Features: Twelve balanced outputs divided among four independent channels. Individual wide range audio output level controls. Separate input and clipping LED's for each 1x3 group. Active balanced outputs with automatic ground sensing for connecting...
Our Price: $2,185.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI BP100-1 Blank 1.2 Inch Panel for SYS10K - Replaces MIDA100 Module - Required When Module Not Present
Item# ATI-BP100-1
ATI BP100-1 is a blank 1.2" panel for the SYS10K. It replaces MIDA 100 module, and is required when module is not present. Specifications: Weight: 0.5lb Dimensions (L x W x H): 11 x 4 x 8"
Our Price: $74.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI BP100-2 Blank 2.0-Inch Front Panel for SYS10K - Replaces Power Supply Module - Required When Module is Not Present
Item# ATI-BP100-2
ATI BP100-2 is a Blank 2.0" Front Panel for SYS10K. It replaces the power supply module, and is required when module is not present. Specifications: Weight: 0.5lb Dimensions (L x W x H): 11 x 4 x 8"
Our Price: $94.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI MIDA100-3 Metered 1X6 Distribution Amplifier Module for SYS10K - Transformer Output with Phoenix I/O
Item# ATI-MIDA100-3
The ATI MIDA100-3 System 10K is the ideal device for multiple distribution when it comes to stereo or mono line amplification, microphone amplification, or headphone distribution. The SYS10K is perfect for any ballpark, museum, or large venue such as the United Nations, where many of our SYS10K systems can be found. The 3RU rack holds up to ten function modules and two power supplies. Each plug-in module is supplied with its own applicable connector assembly, thereby allowing for ease...
Our Price: $1,655.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI PS100-3 Power Supply Module for SYS10K (Two Required for each RM100)
Item# ATI-PS100-3
ATI PS100-3 Power Module--A bi-polar unregulated 18 VDC supply drives the system power buss through fused isolation diodes. Operates singly or as a redundant pair in the right hand positions of each RM100 rack frame. Front panel LEDs indicate low voltage on either buss or blown fuses. Power Failure Alarm relay contacts close for any power loss and can activate an external alarm. Alarm outputs from both PS100 positions are paralleled and brought to a barrier block (terminals 4 & 5) mounted...
Our Price: $878.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI RM100-3 19 Inch Rack Frame for SYS10K - Holds 10 Modules and 2 PS100 Units - Sold Separately
Item# ATI-RM100-3
The ATI RM100-3 SYS10K 10000 combines up to ten amplifier modules with two power modules in a 5-1/4" high by 19" wide Eurocard specification enclosure 14-1/2" deep. All modules plug in from the front, are secured with captive hardware and present an attractive and safe closed front panel. Aluminum extrusion construction makes a strong and rugged enclosure and allows free convection for vertical airflow. The basic frame provides power bussing for all positions. Individual modules are supplied...
Our Price: $1,655.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI SUM100-3 2 to 1 Channel Summing Audio Amplifier - XLR and RCA I/O
Item# ATI-SUM100-3
The ATI SUM100 Summing Amplifier is an inexpensive, high performance amplifier that is designed as a line level stereo to mono summing amplifier. It is also useful as a gain block, and as an impedance converter and summing for IHF (RCA type) signals. The inputs provide balanced 40Kohm bridging impedance for line levels up to +24dBm. The high input impedance allows the SUM100 inputs to also bridge -10dBu (hi-fi, RCA plug) lines without loading. Front panel, screwdriver adjust, full...
Our Price: $505.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ATI Wall Mount Power Supply
Item# WA100-1
This is a wall-mounting power supply, made specifically for the ATI NanoAmp installation line amplifier series, with a 120VAC/60Hz rating.
Our Price: $19.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List

ATI

By Category

By Price Range

Filter By

Narrow Products

By Category

By Price Range

Filter By

Rack Mount For ATI AV8 NanoAmp and MicroAmp

ATI ADA 206-XLR Dual 1x3 Low Noise Analog Audio Distribution Amplifier - XLR Connectors

ATI ADA 416-PHX Quad 1x4 Low Noise Analog Distribution Amplifier- Phoenix Connectors

ATI ADA412-XLR Quad 1x3 Low Noise Analog Distribution Amplifier - XLR Connectors

ATI BP100-1 Blank 1.2 Inch Panel for SYS10K - Replaces MIDA100 Module - Required When Module Not Present

ATI BP100-2 Blank 2.0-Inch Front Panel for SYS10K - Replaces Power Supply Module - Required When Module is Not Present

ATI MIDA100-3 Metered 1X6 Distribution Amplifier Module for SYS10K - Transformer Output with Phoenix I/O

ATI PS100-3 Power Supply Module for SYS10K (Two Required for each RM100)

ATI RM100-3 19 Inch Rack Frame for SYS10K - Holds 10 Modules and 2 PS100 Units - Sold Separately

ATI SUM100-3 2 to 1 Channel Summing Audio Amplifier - XLR and RCA I/O

ATI Wall Mount Power Supply

Sign In

ATI

Narrow Products

By Category

By Price Range

Filter By