-
Item# ATMG-00-502-PG
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-503-MBK
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-202-02
The Active Thermal Management System 2 and 2 + 2 kits are self-contained ventilating systems for small-to-midsize enclosures with moderate heat loads. The major individual components are the 2-speed control unit, power supply, temperature sensor/probe, and two (2) or four (2+2) 4.7 inch/120mm fans. Features: Very quiet
Good for larger cabinets
Larger heat loads
2 speed Specifications: Product: System 2+2 Kit
Fans: 4/120mm
Airflow (free air): 40-80 CFM
Noise level: 23 dBA
Control: Thermal - 2...

-
Item# ATMG-00-301-03
Cool-stack I is the cooling solution for small to mid-sized racks. Connecting to the chassis through a 4' cable, the thermal control lets Cool-stack I's operation be controlled by the temperature of a component in the rack. This means fans can turn on later and stay on until residual heat has been removed from the component being cooled.
Cool-stack I is a 1 RU high true rack-mount ventilator. Very quiet in operation, it mounts above the heat producing equipment and pulls the heated air up and...

-
Item# ATMG-03-123-01
Cool-control is the inexpensive way to add automatic thermal control to manually-controlled cooling systems. Racks that are sold with fans but without thermal control and manually-controlled cooling systems from other manufacturers are easily converted to fully automatic operation with either the rack- or table-mounted Cool-control. As a bonus, Cool-control adds continuous temperature readout on its bright display.
Installation is as easy as plugging the Cool-control into any AC socket and plugging...

-
Item# ATMG-00-100-02
The 00-100-02 is ATM's most powerful and flexible air moving system, the System 1 is available in two versions. The in-line version is suitable for indoor use, while the EXT version is mounted in a weatherproof enclosure, suitable for outdoor use in virtually any climate. Both can move over 100 CFM while producing very little noise, thanks to a precision-balanced rotor. The in-line version is now Energy Star rated; airflow has been increased by 40% to 140 CFM, power...

-
Item# ATMG-00-100-03
The 00-100-03 is ATM's most powerful and flexible air moving system, the System 1 is available in two versions. The in-line version is suitable for indoor use, while the EXT version is mounted in a weatherproof enclosure, suitable for outdoor use in virtually any climate. Both can move over 100 CFM while producing very little noise, thanks to a precision-balanced rotor. The in-line version is now Energy Star rated; airflow has been increased by 40% to 140 CFM, power...

-
Item# ATMG-00-120-01
There are times when a situation calls for the System 1's ability to move hot air through a tube to somewhere else but there's just not enough room for the System 1's tubing or centrifugal blower.
Cool-cube E was developed for the home theater design and installation community. Combining a compact power module with either 4 or 3 flexible tubing, Cool-cube will pull heated air out of a closed mid-size cabinet, small closet, or enclosed video projector and quietly move it to a nearby...

-
Item# ATMG-00-120-04
There are times when a situation calls for the System 1's ability to move hot air through a tube to somewhere else, but there's just not enough room for the System 1's tubing or centrifugal blower.
Cool-cube E was developed for the home theater design and installation community. Combining a compact power module with either 4 or 3 flexible tubing, Cool-cube will pull heated air out of a closed mid-size cabinet, small closet, or enclosed video projector and quietly move it to a nearby...

-
Item# ATMG-00-200-02
The Active Thermal Management System 2, a self-contained ventilating system for small-to-midsize enclosures with moderate heat loads, has been redesigned. It consists of two 120mm fans on a mounting board which also holds a thermal control board with a remote sensor. A small display on the control board is meant for set-up only. It reads in degrees Celsius, not Fahrenheit.
The System 2 is mounted over a 14 1/2" x 5 1/2" rectangular hole (not exact - verify this dimension with the System 2 to be...

-
Item# ATMG-00-201-02
The Active Thermal Management System 2 and 2 + 2 kits are self-contained ventilating systems for small-to-midsize enclosures with moderate heat loads. The major individual components are the 2-speed control unit, power supply, temperature sensor/probe, and two (2) or four (2+2) 4.7 inch/120mm fans. Features: Extremely quiet
Good for mid-size cabinets
2-speed Specifications: Product: System 2 Kit
Fans: 2/120mm
Airflow (free air): 20-40 CFM
Noise level: 21 dBA
Control: Thermal - 2 speeds

-
Item# ATMG-00-302-02
Cool-stack I is the cooling solution for small to mid-sized racks. Connecting to the chassis through a 4' cable, the thermal control lets Cool-stack I's operation be controlled by the temperature of a component in the rack. This means fans can turn on later and stay on until residual heat has been removed from the component being cooled.
Cool-stack I is a 1 RU high true rack-mount ventilator. Very quiet in operation, it mounts above the heat producing equipment and pulls the heated air up and...

-
Item# ATMG-00-304-01
With the height of the Cool-stack I and the depth of the Cool-stack II, Cool-stack III is a 1-unit high hot air exhaust system for mid-size racks with mid-size heat loads! With four 120mm fans and an 18" depth, the Cool-stack III can pull up to 70 CFM of hot air out of tightly-packed racks while generating very low noise levels. Heated air is normally exhausted through the perforated front panel, but exhaust fittings and tubing (provided) can move the hot air safely away to the rear if the rack...

-
Item# ATMG-00-306-01
Cool-rack is a 2 rack-unit high exhaust system for small-to-mid size racks. Moving about 120 CFM very quietly, it is completely automatic, due to a self-contained thermal display and control module. Factory programmed to turn the fans on at 90F and off at 85F, these settings are easily changed in the field using the front panel buttons.
Installation is as easy as mounting the Cool-rack in the rack, plugging the wall-type supply into an AC outlet and its output lead into the Cool-rack's power input...

-
Item# ATMG-00-400-01
The ATM System 3E is a small, thermally-activated ventilation system for smaller installations. Ideal for the bedroom audio system tucked into a nightstand or the CPU in a kitchen cabinet. The System 3 is also ideal for use within a larger enclosure, where pockets of heated air must be dispersed.
Two 80mm fans (3 1/8 square, 1 thick) connect to a small control unit, which also contains plug-in connections for the power supply and thermal probe. The fans are mounted in the enclosure...

-
Item# ATMG-00-401-01
The Small Enclosure Cooler is designed to make cooling smaller enclosures easier than ever. Two 80 mm fans are pre-assembled to a thin panel which mounts over a simple rectangular cutout on a small cabinet's back panel. With a remote thermal probe that easily fastens to the component whose temperature is being monitored, installation is quick and simple.
An important feature of the SEC-1 is its ability to turn on automatically at 90 degrees to deal with the heat generated by today's audio-video...

-
Item# ATMG-00-502-MA
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-502-MBK
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-502-MS
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-503-MA
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-503-MS
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-503-PG
There are some installations in which you can't hide the fan grilles, no matter how hard you try! When vent openings are going to be visible, Cool-vent II or III may be the answer. Shipped in intake mode, each can be reconfigured to quietly move air out of an enclosure, and consists of a fan assembly and a very high quality wood grille. Cast aluminum grilles are also available, made by made by Reggio Register, the leading supplier of HVAC grilles and registers in the U.S.
Cool-vents II and III...

-
Item# ATMG-00-701-18
Designed to quietly cool flat-panel displays recessed into walls or cabinets. While no one device is suitable for ventilating every installation, Cool-stick™ is the answer to many problems. Cool-stick avoids heat problems with its 8 quiet fans blowing a stream of air across the back of a display. Comes with mounting brackets, and is small enough to squeeze behind, below, or above displays in all but the tightest situations. Also useful for mounting behind components in very tight quarters,...

-
Item# ATMG-01-002-02
An equipment cooler that is placed on top of equipment that is running hot. Two silent 4.7 (120mm) fans remove excess heat and prevent damage. Cool-it II is simply placed on top of the overheated receiver, processor or amplifier, the thermal switch is attached and the wall-type power supply is plugged into an always-live outlet. Using the Cool-it II dramatically lowers the temperature of output transistors and nearby components within a receiver or amplifier and will extend its useful life significantly....

-
Item# ATMG-01-008-03
Designed to boost insufficient ventilation for audio and video components. Very slim, it will solve overheating problems where components sit on closely-spaced shelves. Its 1 9/16 height can be reduced to 1 5/16 by removing the Cool-slim's feet. Cools components with and without vent openings in top covers and is temperature-controlled. Not for use in closed cabinets. Features: Silent
Needs no installation
Very low profile
Automatic operation Specifications: Product: Cool-slim
Fans: 4/80mm
Airflow...
