-
Item# ART-SLA1
2 Models AvailableRobust yet compact power amplifier designed for studio and even live applications. It has been designed and engineered to provide clean, quiet power and excellent sound with ultra-low noise and distortion.
Specifications: 100 watts rms/channel @ 8 ohms (130 watts rms/channel @ 4 ohms and 260 Watts/Bridged Mono @ 8 ohms)
input impedance of 22k ohm unbalanced (44k ohm balanced)
XLR & 1.4in I/Os
Ground Lift Switch, Fan Cooled Design, Power, Clip, Signal and Protect LEDs
IU rack Space
Frequency...
Read More
-
Item# ART-PB4X4PROUSB
Presenting the Art PB4x4PROUSB 4x4 PRO USB SERIES Power Distribution Systems from ART. Built on the foundation of the popular 4x4s, the PRO USB SERIES are durably constructed, reliable power conditioners for use in many applications. Wherever power management system is required, the 4x4 PRO USB SERIES provide the surge protection you need to keep your rack safe from unwanted disruption.
All PRO USB SERIES models have an additional internal discrete module called APFT (Advanced Power Filtering)...

-
Item# ART-PS4X4PROUSB
Presenting the 4x4 PRO USB SERIES Power Distribution Systems from ART. Built on the foundation of the popular 4x4s, the PRO USB SERIES are durably constructed, reliable power conditioners for use in many applications. Wherever power management system is required, the 4x4 PRO USB SERIES provides the surge protection you need to keep your rack safe from unwanted disruption.
All PRO USB SERIES models have an additional internal discrete module called APF™ (Advanced Power Filtering)...

-
Item# ART-PROMIX
Each mic channel on the ProMIX has both phantom power and low-frequency cut selectable via DIP switches plus a level control. The balanced XLR line output can be connected to a mic input on the mixer and headphones or a powered monitor can be connected to the Phone/Aux output. And if AC power is not available, the ProMIX runs on batteries as well.

-
Item# TUBE-MP-POWER
Power Supply for ART TUBE MP Microphone Preamp

-
Item# ART-P16
Ideal for any live PA rack, studio rack or fixed installation where easy access to XLR inputs are required, the P16 brings all rear-mounted XLR inputs from various devices to one, convenient single space rackmountable location. The P16 saves wear and tear on the connectors of expensive audio equipment by bringing all commonly used connections to the external patch bay.
All-steel chassis, black anodized finish and secure, high-quality XLR connections front and back with internal connections made...

-
Item# ART-PROSPLIT
The ProSplit provides one direct output and one transformer isolated output from a single microphone. Applications include sending the direct output to the main or Front-of-House mixer, with the second isolated output being sent to a monitor or recording mixer. The direct output passes phantom power from the main mixer to the microphone for use with condenser microphones.
The ProSplit includes a ground-lift switch on the isolated output to reduce noise due to ground loops between connected equipment....

-
Item# ART-DPDB
The new dPDBT Passive Direct Box features two high-quality direct boxes in one portable enclosure. It is a rock solid, roadworthy DI for connection of the outputs of electronic musical instruments (or other audio sources) to the balanced inputs of mixer consoles and other balanced inputs.
It also allows connection of a music source to an instrument amplifier while simultaneously patching it to a mixer. The dPDBT features switchable Input Attenuation (0 dB, -20dB, -40dB), a 50k ohm Instrument...

-
Item# ART-PB4X4
ART 4 x 4 Power Distribution Center
PB 4x4 features ART's "4x4" distribution on the back of the unit -- four of the eight rear outputs are 1.25 inches apart. This allows the user to plug in wide power cables and multiple wall wart devices, and still have eight total power outlets to choose from.
Built into the PB 4x4 is a Surge and Spike Protection System, designed to protect powered equipment from harmful electric surges and spikes. The unit also has RFI and EMI filtering.
The...

-
Item# ART-SP4X4PROUSB
Presenting the SP4X4PROUSB Power Distribution Systems from ART. Built on the foundation of the popular 4x4s, the PRO USB SERIES are durably constructed, reliable power conditioners for use in many applications. Wherever power management system is required, the 4x4 PRO USB SERIES provide the surge protection you need to keep your rack safe from unwanted disruption.
All PRO USB SERIES models have an additional internal discrete module called APF™ (Advanced Power Filtering) which filters...

-
Item# ART-HEADAMP4
The HeadAmp4 offers 1/8th-inch as well as 1/4-inch inputs and outputs as well as lower noise, lower distortion and more output in a new custom extruded stackable metal case.
Ideal for virtually any home or project studio, the ARTcessories HeadAmp4 easily adds additional headphone outputs to any mixer, computer audio interface, workstation, iPod, media player or laptop without creating any additional load on the existing headphone source.
Individual level controls for the four headphone...

-
Item# ART-HEADAMP4PRO
The ART HeadAmp4Pro could be the most fully featured ultra compact headphone amplifier in its price point on the market today.
Packing as many features as possible into the small format chassis, the HeadAmp4Pro has five stereo headphone outs, each with their own volume control. A separate footswitchable XLR input (with phantom power) allows instant talkback to any one, or all of the connected headphones. Input matrix allows the listener to audition any or all auxiliary inputs for maximum...

-
Item# ART-HEADAMP6PRO
The ART HeadAmp6PRO is a six-channel stereo headphone amplifier that includes a six-channel auxiliary input section that can be used to provide the popular "More-Me" function on each headphone mix. Each output channel also features a dual function BALANCE control which will pan between LEFT & RIGHT sides of the main signal bus, or vary the MIX between the main signal bus and the AUXILIARY input for that respective channel.
Bass and treble controls are included on each output channel for fine-tuning...

-
Item# ART-CLEANBOX-2
"Hum" in an audio system is often caused by loop effects which act like antennas. These loops can easily pick up a 60 Hz (or higher harmonics) hum transmitted by electrical wiring. Typically, these loops are connected via grounds, more commonly called "ground loops". The safest way to eliminate unwanted noise is with the CleanBOX II. Some examples of Ground Loops:
-The power ground of a synthesizer, connected to the signal ground of the synth, into a mixer's ground, then into a mixer's power...

-
Item# ART-CLEANBOXPRO
Provides two channels of unbalanced to balanced level conversion in a rugged, compact, and portable unit. Balanced lines offer increased immunity to external electrical noise, such as hum. Since a balanced system minimizes induced noise, it is the preferred method of connecting audio gear, especially when long lengths of cable are used.
One section of the CLEANBoxPro converts two channels of consumer-level unbalanced input signals into two channels of pro line-level balanced output signals. It...

-
Item# ART-T8
The T8 (Transformer Eight) a high quality totally passive audio interface that uses 8 transformers to separate input and output signal grounds, thereby isolating two systems and reducing hum and ground-loop noise. The T8's audio transformers have flat and wide frequency response and handle high signal levels while maintaining an isolated balanced output. This gives the T8 a very clean and neutral sound with a wide variety of signal sources. The transformers are wound for 1:1 unity gain and are designed...

-
Item# ART-DTI
The DTI is a high quality totally passive audio interface that uses a pair of high performance transformers to totally separate input and output signal grounds,thereby isolating two systems and reducing hum and ground-loop noise. The DTI's audio transformers have an extremely flat and wide frequency response and canhandle high signal levels while maintaining an isolated balanced output. This gives the DTI a very clean and neutral sound with a wide variety of signal sources.The transformers are wound...

-
Item# ART-COOLSWITCH
A-Y switching works two ways. It lets you switch a common source signal (guitar, bass or keyboard) between two amplifiers or amp channels. Or conversely, it lets you switch two source signals (ie, two different guitars) into the same amplifier. A good quality A-Y switcher will also provide LEDs or other indicators to show whether A, B or Y routing is in effect. The Y routing combines both the A and B outputs in parallel so that two amplifiers can be driven at once. The CoolSWITCH provides full...

-
Item# ART-SPLITCOMPRO
Use the SPLITCom Pro to Split or Combine balanced low impedance microphone signals.
As a Splitter: The SPLITCom Pro provides one direct-coupled output and one isolated output from a single microphone. Applications include sending the direct output to the main or FOH mixer, and the second isolated output to a monitor or recording mixer. The MAIN MIC OUTPUT passes phantom power from the main mixer to the MAIN MIC INPUT for use with condenser microphones. Phantom power is blocked...

-
Item# ART-S8
The ART S8 can be used to split eight balanced low impedance microphone signals into sixteen balanced low impedance microphone signals (eight pairs).
Each channel of the S8 provides one direct output and one transformer isolated output from a single microphone. Applications include sending the direct outputs to the main or Front-of-House mixer, and the second isolated outputs being sent to a monitor or recording mixer. The direct outputs pass phantom power from the main mixer to the microphones...

Our Price: $279.99
Availability: Extended Lead Time. Email, Chat or Call Us for more details.
Add to Wish List
-
Item# ART-S8-3WAY
The S8-3WAY eight channel three way microphone splitter is ideal for live sound, recording and broadcast applications where microphone and XLR balanced line level input signals have to go to multiple mix locations.
Each channel provides one XLR input, one XLR direct output with two additional transformer isolated XLR outputs for a total of 3 balanced outputs from each single microphone input signal.
Typical uses would include sending 8 direct signals through the S8-3WAY to a main Front-of-house...

-
Item# ART-XCONNECT
The ART XConnect USB Microphone Cable provides an easy way to directly connect any dynamic microphone to your computer''s USB port for convenient recording without any extra equipment. The output of the XConnect is a studio quality 16-bit, 44.1 kHz or 48 kHz digital audio signal. No special drivers are required, just "plug and play" with your Windows PC or Mac.
Simply plug the XLR connector into your microphone and the USB connector into your computer. That''s all there is to it. The first time...

-
Item# ART-SPLITMIX4
The SPLITMix4 is a fully passive hybrid mixer that offers a wide variety of configurations. Mix 4 stereo input channels down to 1 stereo output, split a stereo input signal to distribute 4 stereo output channels, or combine the configurations for a wide range of applications. You can even configure the SPLITMix4 as 4 stereo input channels thru 4 independent level attenuators to 4 stereo output channels.
Independent stereo level controls are provided on each channel. All 1/4-inch connections are...

-
Item# ART-MACMIX
For when you need to mix a CD and a VCR's audio output with a synthesizer and the line output of a bass amp and send it all to a PC or cassette deck. If you are having trouble finding a solution to this dilemma then look no further than the ART MacroMIX. Connect an MacroMIX between your audio sources and the PC or cassette deck. Levels can be mixed and a headphone jack lets you monitor the mix. It's as easy as A,B,C,D & E
Specifications: Four input channels, Ch. 1 and 2 have dual L/R RCA inputs,...

-
Item# ART-USBII
ART is proud to introduce the USB II. This new digital interfaces is a high quality input/output and 192KHz capable digital interfaces for connecting a computer to a wide variety of audio systems.
The USB Dual Pre II takes instrument or mic level signals and converts them with a 32 bit ADC containing sample rates from 44.1kHz to 192kHz for computer input. USB audio is converted using a 32 bit stereo DAC to analog audio. Custom transformers remove ground loops and other system noise between...
