-
Item# RDL-RU-LB4P
The RU-LB4 modules are Dante audio network interface products compatible with line-level audio equipment inputs and outputs. These modules are designed to be mounted in equipment racks, closets, conference tables and on shelves or backboards in commercial/industrial installations.
APPLICATION: The RU-LB4 is a high quality converter that provides professional line-level outputs from four Dante network received audio channels. It also converts four professional or consumer line-level sources to Dante...

-
Item# RDL-DD-BTN44
3 Colors AvailableThe RDL D SERIES-BTN44 modules (DD-BTN44) are Dante networked, wall-mounted audio interfaces that include bidirectional Bluetooth audio, unbalanced analog stereo or mono audio inputs and outputs, and a balanced or unbalanced line-level output. Stereo audio from a compatible Bluetooth-enabled device feeds two Dante network audio channels. Stereo audio connected to a front-panel Mini-Jack or L and R RCA jacks feeds two other Dante network audio channels.
Stereo audio is available to users...
Read More
-
Item# ST-PA6
The ST-PA6 represents the second generation of RDLs breakthrough in the traditional power vs. size ratio. Present technology permits features and performance at the most economical cost ever. The ST-PA6 offers 6 watts of power for a price you would expect to pay for 3 watts.
The ST-PA6 features two balanced audio inputs, a gain control, equalization control and an 8 Ohm output. The output is designed to deliver a clean 6 watts RMS into an 8 Ohm speaker. Each input is a balanced bridge, with the...

-
Item# TX-1A
The RDL TX-1A is used primarily for galvanic isolation and format conversion between equipment. Conversion from -10 dBV consumer level up to +4 dBu professional level requires voltage gain. The transformer in the TX-1A has a 1:1 ratio and uses an adjustable attenuator circuit at its output to lower the output signal to the level required. The module cannot provide voltage gain.
RDL offers several premium quality conversion amplifiers to produce professional signals from consumer sources....

-
Item# ST-PA18
The ST-PA18 features a balanced line level input that may be connected unbalanced. The gain control range will accommodate standard unbalanced levels as well as professional balanced levels. The module bridges the input signal. LOOP OUT terminals permit a balanced input to be fed to additional amplifier modules making the ST-PA18 an ideal component in distributed audio system design. The LOOP OUT may also be used to feed a subwoofer amplifier (see RDL ST-CX2S Subwoofer Filter).
The ST-PA18 output...

-
Item# STD-600
Each STD module is a resistive branching network with RF filtering on each of the four channels. Any channel, A through D, may be either an input or an output. This permits combining stereo signals into mono inputs, splitting mono signals to multiple inputs, and even combining microphones with output shorting switches into a single amplifier input. The STD modules are available in 150 Ohm, 600 Ohm and 10 k Ohm models. All inputs and outputs are balanced. Features: 600 Ohm Operation
Combine Audio...

-
Item# ST-UMX3
The ST-UMX3 is a three-channel audio mixer for combining mic-level or line-level signals to a single output. A MIC/LINE switch is provided for each input. A separate MIC/ LINE switch selects the output level. Each input features a separate preamplifier circuit, which isolates it from the other inputs. An audio taper single turn gain adjustment is provided for each of the three input preamps. Signals from the three preamps are actively summed and fed to the output amplifier which includes an RDL...

-
Item# ST-DA3
The ST-DA3 gives you the advantages of an audio distribution amplifier PLUS you can put it where you need it. The ST-DA3 allows bridging of any audio line, adjusting the gain, and driving up to three high or low impedance, balanced or unbalanced loads. The ST-DA3's wideband circuitry produces the unsurpassed pure clarity, low-distortion and low-noise for which RDL products are known.
The ST-DA3 features RDL's SupplyFlex power input configuration. The module will operate directly from floating...

-
Item# STA1
The STA-1 is a dual-channel line-level preamplifier with bridging inputs, adjustable gain or loss, and low-impedance outputs. Each of the two identical circuits is both an electronic line transformer and a line amplifier. Hook up the STA-1 just like a pair of audio transformers with gain. True dc amplifiers produce unsurpassed audio clarity, high common-mode rejection, ultra-low distortion and low noise. The STA-1 is perfect for most line amplification, impedance or balanced/unbalanced conversion.
The...

-
Item# ST-VCA3
The ST-VCA3 is used in applications requiring smooth audio level control from a remote control panel, potentiometer or dc voltage (0 to 10 V). Installation in series with the audio input of a power amplifier allows remote control of that amplifier's level. For installations where it is preferred to keep the audio localized in the rack, audio controls are extended outside the rack from the ST-VCA3. Many installations benefit from avoiding long-term potentiometer wear from audio running through the...

-
Item# EZ-SX4
The EZ series offers unparalleled flexibility. Each unit is fully labeled on the front and rear for use either as a finished product or as a utility module. Installation of multiple products is quick and easy using the comprehensive range of EZ rack mounts, chassis, bezels, drawers and accessories. High quality full-size switches, long life controls, quality connectors, solid-state audio and video switching, gold plating and superior engineering combine to make EZ the best value in the industry....

-
Item# ST-LCR1
The ST-LCR1 provides double-pole, double-throw dry switching contacts and LED indicator for relay closure. The ST-LCR1 provides momentary operation and is ideally suited where additional switching contacts are needed to be added to nearly any type of control signal.
Features: Add Contacts to Any Control Signal
Activation from Logic Circuits
DPDT Switching Relay
Open-Collector Switching
Control from Switch, Button or Logic Circuits

-
Item# RDL-AV-LN4
The RDL AV-LN4 is an interface that converts four line-level XLR inputs to Dante network audio channels. Special software is not required to configure the AV-LN4. A dual-LED VU meter displays the level for each. The AV-LN4 is a professional grade product for studio quality fidelity and low noise performance.
The AV-LN4 may be powered from an external 24 Vdc power supply, available separately. The AV-LN4 is equipped to operate from a PoE enabled network switch. The AV-LN4 will reserve power...

-
Item# ST-VP2
The ST‑VP2 can be wired into any line‑level input of a paging amplifier. A line‑level music source may be provided from a receiver, satellite decoder, tape or CD source. A line‑level voice source may be provided from a telephone paging system at line level, or from a microphone which has been preamplified up to line level (See RDL STM‑1, STM‑2, STM‑2X, STM‑3, STM‑LDA3 Microphone Preamplifiers).
When a page is initiated, the module automatically...

-
Item# RDL-DD-BN22
The DD-BN22 is a complete wall-mounted Dante audio network interface. It features two XLR mic or line inputs and two XLR mic or line outputs on the front panels. Special software is not required to configure the DD-BN22. Each XLR input provides three switches that may be set from the front of the unit when the cover plate is not installed. One switch enables or disables P48 phantom; the second switch selects the mic or line gain range; the third switch sets the gain. Each XLR output provides a...

-
Item# ST-SH2
The ST‑SH2 is used in applications requiring headphones of any impedance to be driven from consumer or professional audio sources. For fixed level installations not requiring user volume control, the ST‑SH2 is wired to the audio source and to a headphone jack. Frequently, it is desirable to mount a volume knob by the headphone jack. The LEVEL ADJUST terminals (L) and (R) may be wired to the respective wipers of a stereo 10 kΩ potentiometer to provide volume adjustment. It is recommended...

-
Item# ST-SSR1
The ST-SSR1 was designed for absolute silent switching of audio signals. It supports two balanced line-level inputs and one balanced output. Each can be used unbalanced as well. The ST-SSR1 is perfect for switching between two input signals or as a silent On/Off switch for a single channel. Performance is in keeping with the technical standards for which RDL has become known. The user can program the module for either fast or soft switching.
The SELECT input feeds the OUTPUT when the TRIG terminal...

-
Item# RDL-DB-SH1M
The DB-SH1M is used in applications requiring headphones of any impedance to be driven from consumer or professional audio sources. It is ideally suited to applications as diverse as language translation, museums, interview studios and music stores. The -SH1 is a dual channel headphone amplifier with balanced/unbalanced left and right inputs. Each input accepts operating levels between -20 dBV and +20 dBu. Two recessed slide switches located on the side of the rear enclosure are set prior to mounting...

-
Item# TX-70A
Do you ever need to feed the audio from a 70V distributed loud speaker system into a line-level device in a remote location? Do you ever need a few more loudspeakers than your existing 70V amplifier can drive but have no convenient line-level audio to run into a local amplifier?
Well RDL has the module for you!
The TX-70A 70/25/100 volt input interface matches a 100, 70 or 25 volt speaker line to any unbalanced line level audio input. Simply install the TX-70A as you would a 70V speaker...

-
Item# TX-J2
The RDL TX-J2 Unbalanced Input Transformer is part of Radio Design Labs TX Series and features unbalanced stereo inputs to summed balanced mono output.
TX Series modules are application-specific modules for the A/V and related industries. Many TX modules offer galvanic transformer isolation. Module functions include signal detection, switching, amplification, format conversion, line driving, mixing, distribution, twisted-pair sending/receiving and more. Each TX is a compact module...

-
Item# RU-MLD4
The RU-MLD4 is a four channel audio distribution amplifier. The input and all four outputs may be connected through the front-panel XLR jacks or on the rear panel detachable terminal blocks. The input accepts either a balanced microphone or line level signal. Each of the four outputs provides either a microphone or line level signal. Both the front-panel XLR connectors and the rear-panel terminals are active at all times. The RU-MLD4 may be rack-mounted with the XLR jacks facing forward, or may...

-
Item# ST-LCR2
The RDL ST‑LCR2 provides double‑pole, double‑throw dry switching contacts and LED indicator for relay closure. The ST‑LCR2 is used where momentary pulses must alternately toggle on/off switching contacts. Open‑collector slave output allows connection of remote on indicator or an ST‑LCR1 for additional relay contacts.
Features: Alternate‑Action Switching
Add Contacts to Any Control Signal
Activation from Logic Circuits
DPDT Switching Relay
Open‑Collector...

-
Item# RDL-TX-A2
The TX-A2 is the ideal choice in installations requiring passive isolation and level attenuation between a professional balanced line-level mono source and consumer equipment unbalanced inputs.
The TX-A2 is a complete unbalanced line-level audio output module. The front panel provides a detachable terminal block for connection of a balanced +4 dBu audio source. The input signal is coupled to two front-panel gold plated RCA jacks through a studio-quality isolation transformer. Each output is coupled...

-
Item# FP-PA35A
The FP-PA35A is the ideal choice in many applications where multiple 25 V, 70 V or 100 V speakers in a zone need to be powered from a single audio power amplifier.
The FP-PA35A features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted manually or with a trimming screwdriver. The gain range will accommodate standard unbalanced levels as well as professional balanced levels. Multiple distributed sound system speakers connect to...

-
Item# HR-DDA4
The HR-DDA4 is the ideal choice in installations requiring high quality distribution of a digital audio signal. The input and each of the four outputs support AES/EBU, S/PDIF or AES-3ID formats. The HR-DDA4 automatically detects a valid input on any of the four input jacks: S/PDIF optical, S/PDIF coaxial, AES-3ID or AES/EBU. The input is decoded, reclocked and retransmitted to four individually buffered outputs. Front-panel LEDs display the digital audio format and sample rate of a valid source...
