Where to Buy Audio Over CAT5 Extenders

Viewing Item(s):

Display:

Viewing Item(s):

Display

Show As

Sonifex AVN-AIO8 1RU Dante to 8 Mono Channel Analog Input & Output Interface
Sonifex Ltd.
Item# SON-AVNAIO8DANTE
The Sonifex AVN-AIO8 audio converter and interface converts up to eight analogue inputs and eight analogue outputs to and from the Dante Audio-over-IP networking standard. This cost effective 1U rack-mount unit offers an easy solution for AV professionals and system integrators. It is simple to configure and operate, with all set-up done via the standard Dante Controller software and power via PoE (Power Over Ethernet). All analog inputs and outputs are on high-quality Neutrik XLR connectors...
Our Price: $2,097.67
Availability: In Stock
Add to Wish List
Sonifex AVN-AIO8R 8 Input - 8 Output - Dual Dante® Interface - PoE
Sonifex Ltd.
Item# SON-AVN-AIO8R
The AVN-AIO8R audio converter and interface converts up to eight analogue inputs and eight analogue outputs to and from the Dante Audio-over-IP networking standard. Dual Ethernet ports allow the unit to operate in redundant mode, ensuring audio routing is maintained in the event of loss of link on either of the network connections. This cost effective 1U rack-mount unit offers an easy solution for AV professionals and system integrator. It is simple to configure and operate, with all set-up,...
Our Price: $2,173.80
Availability: In Stock
Add to Wish List
RDL D-BT1A Wall Mounted Bluetooth Audio Format-A Interface (White)
Radio Design Labs
Item# RDL-D-BT1A
3 Colors Available
The RDL D SERIES-BT1A modules (D-BT1A) are Bluetooth audio receiving modules compatible with RDL® Format-A twisted pair receivers. When paired with a compatible Bluetooth enabled device, the module receives stereo audio from the Bluetooth source. The stereo signal is sent through two Format-A pairs to any RDL Format-A receiver. A stereo/mono switch set by the installer permits summed mono audio to be sent over one switch-selected pair to the Format-A receiver. If set for stereo operation,...
Read More
Our Price: $386.86
Availability: In Stock
Add to Wish List
Sonifex AVN-DIO09 Microphone Input to Dante Converter
Sonifex Ltd.
Item# SON-AVN-DIO09
The AVN-DIO09 is a Microphone input to Dante converter in the Sonifex DIO range of Dante input/output devices with A/D circuitry offering a world-class E.I.N. of 129dB. It features a single high quality mic preamp with balanced XLR input, coarse and fine gain controls, high pass filter, phantom power, tri-color level LED and one Neutrik EtherCon® connector for direct connection to a Dante AoIP network. All Sonifex DIO interfaces provide a simple, convenient, and elegant plug and play...
Our Price: $667.40
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
RDL TX-TPR3A Active Three-Pair Receiver Twisted Pair Format-A - Balanced Line
Radio Design Labs
Item# TX-TPR3A
The TX-TPR3A is a three-pair audio receiving module compatible with RDL Format-A twisted pair products. Three outputs are provided corresponding to the three signal pairs A, B and C. The audio signal received on each pair of the RJ45 INPUT jack feeds the corresponding -10 dBV unbalanced RCA phono jack output and the +4 dBu balanced detachable terminal block output. A studio-quality buffer amplifier feeds the outputs at the correct operating level. The TX-TPR3A features bridging inputs, allowing...
Our Price: $204.91
Availability: In Stock
Add to Wish List
RDL D-TPS1A Active Single-Pair Sender - Twisted Pair Format-A - XLR w/ Phantom
Radio Design Labs
Item# RDL-D-TPS1A
The -TPS1A modules are single-pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The D- and DS- models mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes. The D-TPS1A features a white front-panel laminate with gray lettering that matches RDL Decora-style remote controls. The DS-TPS1A is constructed of stainless steel...
Our Price: $226.50
Availability: In Stock
Add to Wish List
Sescom SES-4XLRF-CAT 4 Channel Passive Balanced Audio Extender Snake over CAT5/6/7 - RJ45 to 4 Female XLR Connectors
Sescom
Item# SES-4XLRF-CAT
6 XLR Genders and 2 Form Factors Available
Save big on the costs of expensive XLR audio snakes and pair-down 4 cable channels into a single low profile run with the Sescom 4XLRF-CAT. This brilliantly simple solution allows you to convert 4 XLR channels to single RJ45 connection allowing balanced mic level, AES/EBU digital or DMX signals to be run over a single CAT5, CAT5e, CAT6 or CAT7 cable. Run only the channels you need and even take advantage of the Sescom 4XLRF-CAT versatility by mixing multiple signals types in the same setup....
Read More
Our Price: $106.95
Availability: In Stock
Add to Wish List
SoundTools CATRACK-FX XLR Audio Over CAT5 Rack Unit with etherCON Connectors - 12 Female XLR
SoundTools
Item# CATRACK-FX
The SoundTools CAT Rack FX is a 1RU 12 female XLR rack unit with Main and Parallel etherCON connectors capable of receiving up to 12 lines of balanced analog audio down 3 shielded CAT5 cables. The CAT Rack consists of 12 Neutrik XLR connectors and 6 Neutrik etherCON connectors. The 12 channels are broken down into three sets of 4 channels marked A, B, and C, which are transported down a shielded CAT5 cable. Each line can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds...
Our Price: $250.00
Availability: In Stock
Add to Wish List
RDL D-TPSM2A Active Two-Pair Sender - Dual Microphone Preamplifier - Twisted Pair Format-A - White
Radio Design Labs
Item# RDL-D-TPSM2A
The D SERIES-TPSM2A modules are two-pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The TPSM2A models mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes. The D-TPSM2A features a white front-panel laminate with gray lettering that matches RDL Decorac-style remote controls. The DB-TPSM2A features a black front-panel...
Our Price: $332.96
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
RDL TX-TPR1A Active Single-Pair Receiver - Twisted Pair Format-A - Bal Line Out
Radio Design Labs
Item# TX-TPR1A
The RDL TX-TPR1A is a single-pair audio receiving module compatible with RDL Format-A twisted pair products. A front-panel switch set during installation determines which of the three FORMAT-A pairs is buffered to feed the module output. The audio signal received from the selected pair of the RJ45 INPUT jack feeds the -10 dBV unbalanced RCA phono jack output and the +4 dBu balanced detachable terminal block output. A studio-quality buffer amplifier feeds the outputs at the correct operating...
Our Price: $179.80
Availability: In Stock
Add to Wish List
MuxLab 500030 Stereo-PC Audio Over Cat5 Balun
MuxLab Inc
Item# MUX-500030
The Stereo PC-Audio Balun allows unbalanced line level stereo analogue audio to be transmitted via Category 5/6 unshielded copper twisted pair (UTP) in a point-to-point connection. The product is designed for audio equipment equipped with 3.5mm line-level stereo output such as PC sound cards, laptops and multi-media servers where midrange audio frequency response is required. The Stereo PC-Audio Balun works in pairs or in conjunction with other MuxLab products such as the 500019, 500001, 500012,...
Our Price: $35.00
Availability: In Stock
Add to Wish List
Studio Hub ADAPT-XLRF XLR Female to RJ-45
StudioHub
Item# ADAPT-XLRF
Adapts SH+ cables to source equipment. StudioHub+ is the CAT5 wiring standard of shielded cables, adapters and connectors, all made to plug-and-play your studio. Add powered panels, matchjacks, tie-lines, patch panels and switchers to expand connectivity and functionality.
Our Price: $21.00
Availability: In Stock
Add to Wish List
RDL D-TPS7A Passive Single-Pair Sender
Radio Design Labs
Item# RDL-D-TPS7A
The -TPS7A is a single-pair audio sending module compatible with RDL® Format-A twisted pair products. The front panel features a single stereo mini-jack intended for stereo consumer line level audio sources. A studio-quality transformer provides isolation between the audio source and the RJ45 TP CABLE.The -TPS7A is a single-pair sender, feeding the input signal to the cable pair set on the rear-panel switch during installation. This module drives only one cable pair, therefore a TP CABLE...
Our Price: $103.02
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ETS PA202M Instasnake Adaptor - 4 MXLR to RJ45 Jack All Pins
ETS
Item# ETS-PA202M
The ETS InstaSnake Series (PA200) gives a compact, lightweight, versatile passive group of components allowing you to run audio signals over a single run of CAT5 or 5E or 6 cables. With a roll of wire, these compact units are easily transported and/or stored solving dozens of live and/or recording sound problems. You can mix and match Mic/Line, Line or AES/EBU configurations making the InstaSnake a versatile high quality solution at affordable prices. The basic units are passive units with bi-directional...
Our Price: $154.55
Availability: In Stock
Add to Wish List
SoundTools CATRACK-MX 12 Male XLR Audio Over CAT5 Rack Unit w/ etherCON Connectors for Shielded Cat5 Cable
SoundTools
Item# CATRACK-MX
The SoundTools CAT Rack MX is a 1RU 12 male XLR rack unit with Main and Parallel etherCON connectors capable of receiving up to 12 lines of balanced analog audio down 3 shielded CAT5 cables. The CAT Rack consists of 12 Neutrik XLR connectors and 6 Neutrik etherCON connectors. The 12 channels are broken down into three sets of 4 channels marked A, B, and C, which are transported down a shielded CAT5 cable. Each line can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds...
Our Price: $250.00
Availability: In Stock
Add to Wish List
Sescom SES-3XLRF-CAT 3 Channel Passive Balanced Audio Extender Snake over CAT5/6/7 - RJ45 to 3 Female XLR Connectors
Sescom
Item# SES-3XLRF-CAT
2 XLR Genders and 2 Form Factors Available
Save big on the costs of expensive XLR audio snakes and pair-down 3 cable channels into a single low profile run with the Sescom 3XLRF-CAT. This brilliantly simple solution allows you to convert 3 XLR channels to single RJ45 connection allowing balanced mic level, AES/EBU digital or DMX signals to be run over a single CAT5, CAT5e, CAT6 or CAT7 cable. Run only the channels you need and even take advantage of the Sescom 3XLRF-CAT versatility by mixing multiple signals types in the same setup....
Read More
Our Price: $88.49
Availability: In Stock
Add to Wish List
SoundTools CATBOX-FX Four Female XLR Audio Over CAT5 Stage Box w/ etherCON Connectors - Use Shielded CAT5 Cable
SoundTools
Item# CATBOX-FX
The SoundTools CAT Box FX Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5, CAT5e, CAT6 or CAT7 cable. Each CAT Box stage box has an etherCON input and an etherCON parallel output that allows the CAT Box to be used as a hard-wire split. You can run 4 stereo AES lines down a single shielded CAT5/5e/6 cable for a longer distance AES signal. CAT5e is superior for carrying AES signals over longer distances than conventional 4-channel audio snakes. The...
Our Price: $130.00
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
SoundTools Systems WallCAT 8 Two Gang Wall Panel with 4 Female and 4 Male XLR to RJ45
SoundTools
Item# RSS-WALLCAT8
The SoundTools WallCAT is designed to transport audio easily and conveniently from one room to the next utilizing shielded CAT5/6/7 cable. Each WallCAT has an input and parallel RJ45. That enables audio to be sent from one room to multiple locations or from multiple locations to a single room. Audio Over Cat5 Wall Mount Send audio and data from one room to another using installed shielded Cat5 cable and SoundTools Wall CATs. These durable aluminum wall units fit standard 4" electrical...
Our Price: $80.00
Availability: In Stock
Add to Wish List
GEFEN EXT-DIGAUD-141 Digital Audio Extender
Gefen Inc
Item# EXT-DIGAUD-141
Place your digital audio components anywhere you want with Gefen's Digital Audio Extender. It supports either S/PDIF or TOSlink digital audio signals, which are commonly used to transmit stereo and multichannel (5.1, DTS, Dolby Digital, etc.) digital audio among various components. The Digital Audio Extender uses a sender and receiver system connected by CAT-5E cables to extend the digital audio. Features: Audio is transmitted digitally for zero signal loss Extends any S/PDIF and TOSlink...
Our Price: $193.47
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
ETS PA202P InstaSnake Adapter - 4 MXLR 1.5 ft pigtail to RJ45 Jack All Pins
ETS
Item# ETS-PA202P
The ETS InstaSnake Series (PA200) is a compact, lightweight, versatile passive group of components allowing you to run audio signals over a single run of CAT5, 5E or 6 cables. With a roll of wire, these compact units are easily transported and/or stored solving dozens of live and/or recording sound problems. The InstaSnake is a passive unit, so you do not need power. The InstaSnake accepts "mic" level, analog or digital audio and supports phantom power when using shielded Cat5 or 6 cables. TheThe...
Our Price: $191.07
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
Radio Design Labs D-J3M Mic/Line Input Assembly - XLR - Mini Jack - Terminal Block
Radio Design Labs
Item# RDL-D-J3M
The D SERIES-J1, -J2 and -J3 are audio input accessories from Radio Design Labs offered in Decora® plates. The D SERIES panels are finished in RDL's grey/white, black or in stainless steel. These input panels are intended for installations demanding the ultimate in professional styling combined with durability, longevity and value. The D SERIES-J1, -J2 and -J3 fit directly into RDL back boxes (WB-1U, WB-2U) to fit cabinets, US or international walls. The back of each panel assembly is...
Our Price: $70.66
Availability: In Stock
Add to Wish List
ETS PA203F InstaSnake Adapter - 3 FXLR 1 MXLR to RJ45 Jack All Pins
ETS
Item# ETS-PA203F
3 Versions Available
The ETS InstaSnake PA203 Series is configured for 3 sends and 1 return. Each passive send unit (PA203F) features 3 Female XLR and 1 Male XLR to RJ45 jack, all pins. Each passive receive unit (PA203M) features 3 Male XLR and 1 Female XLR to RJ45 jack, all pins. The ETS-PA203P adds the convenience or an 18" XLR Pigtail at the receive end. The basic units are a pair of passive units with bi-directional capability which can be input...
Read More
Our Price: $164.93
Availability: In Stock
Add to Wish List
ETS PA205F InstaSnake 3-Channel XLR Female CAT5 Audio Balun
ETS
Item# ETS-PA205F
The ETS InstaSnake PA200 Series is configured for 3 sends and 1 return. Each passive send unit (PA205F) features 3 Female XLR and 1 Male XLR to RJ45 jack, all pins. Each passive receive unit (PA205M) features 3 Male XLR and 1 Female XLR to RJ45 jack, all pins. The PA205 will send phantom power over standard Cat5 or 6 cables. Phantom power has been tested to 850 feet over shielded cable. The basic units are a pair of passive units with bi-directional capability which can be input directly into...
Our Price: $157.87
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
ETS PA205M InstaSnake 3-Channel XLR Male CAT5 Audio Balun
ETS
Item# ETS-PA205M
The ETS InstaSnake PA200 Series is configured for 3 sends and 1 return. Each passive send unit (PA205F) features 3 Female XLR and 1 Male XLR to RJ45 jack, all pins. Each passive receive unit (PA205M) features 3 Male XLR and 1 Female XLR to RJ45 jack, all pins. The PA205 will send phantom power over standard Cat5 or 6 cables. Phantom power has been tested to 850 feet over shielded cable. The basic units are a pair of passive units with bi-directional capability which can be input directly into...
Our Price: $157.87
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
MuxLab 500028 RCA Stereo Audio Hi-Fi Balun 2-Pack
MuxLab Inc
Item# MUX-500028-2PK
The Stereo Hi-Fi Balun allows unbalanced linelevel stereo analog audio to be transmitted via Category 5 unshielded copper twisted pair(UTP) in a point-to-point connection. Theproduct is designed for audio applicationswhere full-range, hi-fidelity audio frequencyresponse is required. Used in pairs, the Stereo Hi-Fi Balun eliminatescostly and bulky coaxial cable, allowing audioequipment to be connected or moved within astructured cabling environment. Features: 20 Hz to 20 KHz bandwidth Cost-efficient...
Our Price: $72.00
Availability: In Stock
Add to Wish List
ETS PA202F InstaSnake Adapter - 4 FXLR to RJ45 Jack All Pins
ETS
Item# ETS-PA202F
The ETS InstaSnake Series (PA200) gives a compact, lightweight, versatile passive group of components allowing you to run audio signals over a single run of CAT5 or 5E or 6 cables. With a roll of wire, these compact units are easily transported and/or stored solving dozens of live and/or recording sound problems. You can mix and match Mic/Line, Line or AES/EBU configurations making the InstaSnake a versatile high quality solution at affordable prices. The basic units are passive units with bi-directional...
Our Price: $154.55
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
MuxLab 500033 VideoEase Quad Audio Balun
MuxLab Inc
Item# MUX-500033
The VideoEase Quad Audio Balun allows up tofour (4) analog line audio signals to betransmitted via unshielded twisted pair (UTP)cable in a point-to-point connection. Used in pairs, the Quad Audio Balun allows upto four (4) coax audio cables to be replaced byone (1) Cat5 cable. The Quad Audio Balun alsoworks in conjunction with other MuxLab analogaudio baluns such as the 500019. Features: Cost-efficient cabling - save up to four (4)cables Analog audio up to 5,000 ft (1.5 km) via Cat 5 ...
Our Price: $51.00
Special Price: $45.05
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Studiohub ADAPTM-XLRFS RJ-45 Male to Single XLR Female Adapter - 6 Inch - Balanced
StudioHub
Item# SOHB-ADAPTMXLRFS
So many broadcast products are now equipped with StudioHub+ connectors. Sometimes, you need to turn that into XLR right at the source/destination. A six inch cable length with a male RJ45 at one end and XLR connector(s) at the other. Dual XLR versions for stereo analog, single XLR versions for mono analog or AES/EBU digital audio. StudioHub adapters are available with the most popular audio connectors. Each is terminated with an RJ45 connector. Use these adapters with one of our shielded CAT5 patch...
Our Price: $17.00
Availability: In Stock
Add to Wish List
MuxLab 500028-F-2PK Stereo Hi-Fi Balun - 2 Pack
MuxLab Inc
Item# MUX-500028-F-2PK
The MuxLab 500028-F-2PK Hi-Fi Balun allows unbalanced line level stereo analogue audio to be transmitted via Category 5e/ 6 unshielded copper twisted pair (UTP) in a point-to-point connection. The product is designed for audio applications where fullrange, hi-fidelity audio frequency response is required. Used in pairs, the Stereo Hi-Fi Balun eliminates costly and bulky coaxial cable, allowing audio equipment to be connected or moved within a structured cabling environment. Features:...
Our Price: $72.00
Availability: In Stock
Add to Wish List
MuxLab 500027 Stereo Audio Balun
MuxLab Inc
Item# MUX-500027
Muxlab's500027 allows an unbalanced line-level stereo signal to be transmitted via a single Cat5e/6 cable in a point-to-point connection to distances of up to 5,000 feet/1.5km! Perfect for audio applications where your priority is mid-range audio frequency response. Used in pairs this Stereo/Audio Balun can be used in conjunction with the MUX-500030 audio balun to connect an RCA interface to a 3.5mm audio interface. The Stereo Audio Balun also works inconjunction with other MuxLab products...
Our Price: $35.00
Availability: In Stock
Add to Wish List
Studiohub ADAPTM-XLRMS RJ-45 Male to Single XLR Male Adapter - 6 Inch - Balanced
StudioHub
Item# SOHB-ADAPTMXLRMS
So many broadcast products are now equipped with StudioHub+ connectors. Sometimes, you need to turn that into XLR right at the source/destination. A six inch cable length with a male RJ45 at one end and XLR connector(s) at the other. Dual XLR versions for stereo analog, single XLR versions for mono analog or AES/EBU digital audio. StudioHub adapters are available with the most popular audio connectors. Each is terminated with an RJ45 connector. Use these adapters with one of our shielded CAT5 patch...
Our Price: $17.00
Availability: In Stock
Add to Wish List
Radio Design Labs DB-J3M Mic/Line Input Assembly - XLR - Mini Jack - Terminal Block - Black
Radio Design Labs
Item# RDL-DB-J3M
The D SERIES-J1, -J2 and -J3 are audio input accessories from Radio Design Labs offered in Decora® plates. The D SERIES panels are finished in RDL's grey/white, black or in stainless steel. These input panels are intended for installations demanding the ultimate in professional styling combined with durability, longevity and value. The D SERIES-J1, -J2 and -J3 fit directly into RDL back boxes (WB-1U, WB-2U) to fit cabinets, US or international walls. The back of each panel assembly is...
Our Price: $70.66
Availability: In Stock
Add to Wish List
DSan CAT5-ADP-L 6-Foot XLR to Cat-5 Cable Adapter for use with Podium Signal Light PSL-20V
DSan Corporation
Item# DSA-CAT5-ADP-L
This DSan CAT5-ADP-L is an adapter from Male XLR to Modular Cat 5 Jack, which allows a wired connection between two PerfectCues or for use with Sentry or PC-AS2HW, using XLR cable. Features: Specifications: Product Dimensions: 6' long Weight: 5 oz.
Our Price: $30.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
MuxLab 500028-WP-US Stereo Hi-Fi Wall Balun
MuxLab Inc
Item# MUX-500028-WP-US
The Stereo Hi-Fi Wall Balun (500028-WP-US)allows unbalanced line level stereo analogue audio to be transmitted via Category 5e/6unshielded copper twisted pair (UTP) in a point-to-point connection. The product is designed for audio applications where full-range, hi-fidelity audio frequency response is required. Used in pairs, the Stereo Hi-Fi Wall Balun eliminates costly and bulky coaxial cable, allowing audio equipment to be connected or moved within a structured cabling environment. Features:...
Our Price: $59.00
Availability: In Stock
Add to Wish List
RDL DS-XLR2 XLR 3-pin Female & 3-pin Male on Decora Wall Plate with Terminal Block connections on rear
Radio Design Labs
Item# RDL-DS-XLR2
RDL DS-XLR2 XLR 3-pin Female and 3-pin Male on Decora Wall Plate with Terminal Block connections on rear. Features: Specifications:
Our Price: $29.94
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ETS AV822 HD Component Video Plus Stereo Audio 5 RCA to RJ45 to 2 JR45
ETS
Item# ETS-AV822
The ETS AV-822 is a High Definition Component Video + Audio Balun for ease of use and consistent signal labeling in applications that utilize component video signals. Component video formats include RGB, YUV, YIQ and YCrCb. High Definition Component Video + Digital Audio + Analog Stereo Audio + IR or Data Pass Through is for high-end home and professional theaters that transmits signals from 480p to 1080p resolution video. Features: HDCVB + Stereo Audio, (5) RCA jacks to (2) RJ45 jacks Video:...
Our Price: $161.60
Availability: Ships Factory Direct, Typically in 3-10 Business Days
Add to Wish List
ETS PA203FP InstaSnake Send 3 Female XLR and 1 Male XLR 1.50 Foot with Pigtail to RJ45 Jack- All Pins
ETS
Item# ETS-PA203FP
The ETS InstaSnake™ Series (PA200) is a compact, lightweight, versatile passive group of components allowing you to run audio signals over a single run of Cat 5, 5e, 6 or 6a data cables. With a roll of cable, these compact units are easily transported and/or stored solving dozens of live and/or recording sound problems. Designed to the highest professional standards the InstaSnake™ has a wide, flat frequency response, low THD and residual noise. The InstaSnake™ has been factory...
Our Price: $191.07
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ETS PA204M InstaSnake - Receive (2) FXLR plus Receive (2) MXLR to RJ45 Jack - All Pins
ETS
Item# ETS-PA204M
The ETS InstaSnake PA204M is a passive network audio snake featuring two male XLR sends, two female XLR returns, and one RJ45 ethernet jack. The PA204M allows you to run audio signals over a single run of CAT5, 5e, 6 or 6a data cables. The passive InstaSnake doesn't need power, and it accepts mic or line level analog or digital audio, supports phantom power when using shielded CAT5 or 6 cables. The unit also features bi-directional capability which can input directly into analog or digital...
Our Price: $164.93
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ETS PA875 Balanced Analog Audio - 6.00 Pigtail MXLR to RJ45 Pins 5 and 4
ETS
Item# ETS-PA875
The ETS PA875 Series of Balanced Analog Audio Adapters is ideal for use in applications requiring audio signals to be sent over distances greater than 4 meters. Signals may be sent in either direction. By balancing the audio signal as well as isolating it, signals can be easily sent over 100 meters distance. Features: Full audio bandwidth Minimizes spurious signal ingress Eliminates ground loops Compact plastic case Made in USA 100% tested Specifications: Bandwidth:...
Our Price: $58.65
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ETS PA876 Balanced Analog Audio Adapter with 6 Inch Pigtail FXLR to RJ45 Pins 5 and 4
ETS
Item# ETS-PA876
The ETS PA876 is a balanced analog audio Adapter with a 6 inch pigtail female XLR to RJ45 pins 5 and 4. The ETS PA870 Series of Balanced Analog Audio Adapters is ideal for use in applications that require audio signals to be sent over distances greater than 4 meters. Signals may be sent in either direction. By balancing the audio signal as well as isolating it, signals can be easily sent over 100 meters distance. Perfect for Churches, Theaters, Classrooms, Auditoriums or anywhere...
Our Price: $58.65
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Jackreel Balanced XLR over CAT5 with 100 Foot of Belden 1583 Datatwist Cable
JackReel Cable Reels
Item# MKR-AR-100
3 Lengths Available
Our new Connect-N-Go Series AV over Cat5 reels are designed to deliver all of today's most popular video & audio media over long distances while offering fast plug and play tangle-free deployment. AV balun systems reduce cost, reduce weight and extend distances. Each reel supports point to point connections over CAT5 for any application from Component HD to balanced audio. Typical applications include live video for ENG and sports events, house of worship AV, live sound security video, digital signage,...
Read More
Our Price: $201.49
Availability: Extended Lead Time. Email, Chat or Call Us for more details.
Add to Wish List
Speco UTPAUDIO 1 Mile Audio Over CAT5E Extender
SPECO
Item# SPC-UTPAUDIO
Send Audio up to 1 mile over CAT5E Features: Send Audio up to 1 mile over CAT5E Specifications:
Our Price: $27.54
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
ESI PLANET 22X Professional 2-In/2-Out Dante Audio Interface
ESI
Item# ESI-PLANET-22X
ESI planet 22x is a revolutionary new audio interface that combines the most modern networking audio technology based on the popular Dante protocol with the requirements of a professional high end desktop recording audio interface in studio and in mobile environments. The audio interface is equipped with ultra high quality 24-bit / 96kHz AD converters with 118dB(a) dynamic range and 24-bit / 96kHz DA converters with 123dB(a) dynamic range. The two balanced analog line inputs can also be...
Our Price: $499.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Vanco 280531 Digital Audio Over Cat5e/Cat6 Cable Extender
Vanco Inc
Item# VCO-280531
Allows digital signals to be transmitted using a single Cat5e or Cat6 cable. Features: Transmission Range: Up to 330 ft (100 meters) Accepts Digital Coax or Optical Toslink Supports Digital 5.1 (DTS, Dolby Digital, etc.) High performance, zero signal loss Data Transmission Rate: 12.8 Mb/s S/PDIF (Digital Coax): 96 kHz performance Power Supply: 12V DC, transmitter side Dimensions: 2.75" W x 1.25" H x 2.5" D
Our Price: $183.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Vanco 280535 Analog Audio Over Cat5E/Cat6 Cable Extender
Vanco Inc
Item# VCO-280535
Allows analog audio signals to be transmitted using a single Cat5e or Cat6 cable. Features: Transmission Range: Up to 600 meters (1968 ft) Switch allows for choice between stereo audio or mini stereo audio Audio Input: Dual gold-plated RCA female jacks or 3.5mm stereo jack Output: RJ45 High performance eliminates audio ground loop issues Passive, no power required Dimensions: 4.25" W x 1" H x 2.8" D
Our Price: $98.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Radial Catapult RX4L Cat 5 Analog Snake Receiver with 4 Line Level Isolated XLRM Outputs & 1 Set of Pass-through XLRM
Radial Engineering
Item# RAD-CATAPULTRX4L
Receive module with 4 line-level (-20 to +15dB) isolated XLR-M outputs and one set of pass-through XLR-Ms The Radial Catapult is a modular snake system that drives four analog or AES audio channels over a single shielded Cat 5 cable. The Catapult enables system contractors to take advantage of pre-wired networks to connect one room to another, and allows live sound technicians to take advantage of the low cost of Cat 5 cable for return or cross-stage snakes. The modular Catapult is available...
Our Price: $289.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Radial Catapult TX4L Cat 5 Analog Snake Transmitter with 4 XLR Inputs & 4 Line Level Isolated XLR-M Outputs
Radial Engineering
Item# RAD-CATAPULTTX4L
Transmit module with 4 XLR inputs and 4 line level (-20 to +15dB) isolated XLR-M outputs The Radial Catapult is a modular snake system that drives four analog or AES audio channels over a single shielded Cat 5 cable. The Catapult enables system contractors to take advantage of pre-wired networks to connect one room to another, and allows live sound technicians to take advantage of the low cost of Cat 5 cable for return or cross-stage snakes. The modular Catapult is available in six configurations...
Our Price: $289.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Radial Catapult TX4 Cat 5 Analog Snake Transmitter with 4 XLR-F Inputs and 4 XLR-M Outputs
Radial Engineering
Item# RAD-CATAPULTTX4
Transmit module with 4 XLR-F inputs and 4 XLR-M outputs The Radial Catapult is a modular snake system that drives four analog or AES audio channels over a single shielded Cat 5 cable. The Catapult enables system contractors to take advantage of pre-wired networks to connect one room to another, and allows live sound technicians to take advantage of the low cost of Cat 5 cable for return or cross-stage snakes. The modular Catapult is available in six configurations with a choice of three input...
Our Price: $229.99
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Attero Tech Axon A4FLEX 4-Ch Mic/Line I/O Interface with Logic I/O - PoE+ or 24VDC - AES67 2x5W Power Amplifier
Attero Tech
Item# ATEC-AXON-A4FLEX
The Attero Tech AXON A4FLEX is a compact and scalable mic/line connectivity solution for Dante™ and AES67 networked AVC systems. With four mic/line inputs (two of which are flex I/O and can be outputs), USB and AES67 audio and control interfaces, logic inputs and outputs, and a two-channel power amplifier the A4FLEX is equally suited to be the heart of a huddle space, small conference room, or I/O extension to a wide variety of DSP platforms. The A4FLEX can be a key part of conferencing...
Our Price: $1,717.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List
Attero Tech Synapse D32o 32 Channel Line Out Dante/AES67 Interface 1RU
Attero Tech
Item# SYNAPSED32O
The Attero Tech D32o is a high performance, high channel density networked audio interface supporting Dante™ with AES67 interoperability. The balanced line level outputs feature digitally controlled output attenuation from 0 to -100 dB. All outputs are available independently for routing from the Dante™ / AES67 network audio interfaces. The D32o is available in terminal block or DB-25 options for optimum ease of connectivity and wiring. Features: 32 balanced line level outputs...
Our Price: $4,435.00
Availability: Typically Ships in 3-10 Business Days
Add to Wish List

Mic cables, individually, can amount to a hill of trouble! Audio snakes cleared up the "spagetti" mess but are still heavy and cumbersome and FOH engineers know that the greater the distance to the stage the more you increase your chances of RF and signal loss. Converting audio signals over to ethernet with the use of Audio Over CAT5 Extenders and a single Cat 5 cable will allow you to carry the equivalent of 4 mic signals well over 1000 feet using standard dynamic mics with virtually no delay or signal loss. UsingAudio Over CAT5 Extenders can also shorten your setup and breakdown times. Do yourself and your back a favor, buy a few sets of Audio Over CAT5 Extendersfrom Markertek.

Sign In

Audio Over CAT5 Extenders

Narrow Products

By Brand

By Price Range

Filter By