-
Allen & Heath USA
Item# AH-AP12151
The Allen and Heath AH-AP12151 is a Dust Cover that is designed to cover and protect the Allen & Heath Avantis 64 channel / 42 configurable bus console when it's not in use. (Console sold separately)

-
Allen & Heath USA
Item# AH-LEDLAMP-X
LEDLamp is a variable brightness 18" gooseneck lamp for mixing console and other equipment illumination using LEDs (light emitting diodes) instead of a filament bulb. The LEDs are angled at 40 degrees ensuring a suitably wide light dispersion. Producing a bright, white light, the LEDLamp is more relaxing on the eye and better suited to illuminating a console control surface than the yellow light of a filament bulb. Unlike the filament bulb, the LEDs do not produce heat and they do not require replacement...

-
Allen & Heath USA
Item# AH-M-DL-GACE-A
The gigaACE audio networking card (M-DL-GACE) is one of several audio networking options that can be fitted to any Allen & Heath dLive or Avantis I/O Port. It provides a 128x128ch 96kHz gigaACE point-to-point link to another dLive or Avantis mixing system. It also enables connection from a dLive system to the DX Hub or GX4816 expander.
gigaACE is Allen & Heath's proprietary protocol for transporting Audio and Control over Ethernet, using standard CAT cables. It allows very low latency and cable...

-
Ashly Audio
Item# ASH-DANTE-3018
The optional Ashly Dante-3018 module allows the digiMIX18 to receive and transmit audio with other Dante devices. Configuration of Dante audio streams requires the use of Dante Controller. This free software from Audinate is available for both Windowsr and Macr. Dante Controller uses a simple matrix (shown on next page) to connect Dante audio transmitters with receivers. The Dante-3018 provides access for up to 18 digital audio input channels and 30 digital audio output channels on the digiMIX18.
Any...

-
Rolls Corporation
Item# BC17
The Rolls BC17 belt clip for the PM series to attach to clothing.
Works with the PM50s PM50sOB and PM350
Features: Spring steel with mounting screws

-
TOA Electronics, Inc.
Item# D-001R
The D-001R is a line input plug-in module designed for use with
the M-9000. It has 2-channel unbalanced input of RCA jacks.
Input signals to both channels are mixed together. The D-001R
can process effect for TONE/EQ/COMPRESSOR to two inputs
independently.
Specifications: Power Requirement +24 V DC, -24 V DC, +6 V DC
Current Consumption 20 mA (at +24 V DC), 20 mA (at -24 V DC), 60 mA (at +6 V DC)
Intput 2 channels, 2 RCA/ch mixed, 10 k ohms, unbalanced, RCA pin jack
Intput Sensitivity -60,...

Our Price: $157.00
Availability: Direct Ship from manufacturer, contact us for availability
Add to Wish List
-
-
-
-
-
-
PreSonus
Item# PRE-SL1602-COVER
Dust Cover for PreSonus StudioLive 16.0.2 Mixer The Dustcover for StudioLive 16.0.2 Digital Mixer from PreSonus is made of black canvas and protects the control surface - sides - and rear panel of the 16.0.2 mixer. Features: Specifications:

-
PreSonus
Item# PRE-SL1642-BAG
The PreSonus SL1642-BAG backpack will protect your StudioLive 16 Series III, 16.4.2AI mixer or CS18AI Control Surface from the rigors of the road. This soft case is padded and features a tough ballistic nylon exterior to keep your precious equipment free from dust and scratches, and ward off the onslaught of any sharp implements that may be lurking in the vicinity on any given day of your tour schedule. You also get handles, a padded shoulder strap for dashing through airports, a side zipper...

-
Stewart Audio, Inc.
Item# STW-NETAV-IO2X2D
The NetAV I/O 2x2 is a simple digital on or off ramp for Dante applications. With the world fast moving into the digital age there remain plenty of legacy devices that are analog, the NetAV I/O 2x2 is the easiest way to bring them into the digital realm. With two balanced analog inputs (line level, Mic and 24V phantom power) that are automatically encoded, any analog audio signal can be made available to the network. By the same token any Dante signal on the network can be converted to an analog...

Our Price: $534.57
Availability: Extended Lead Time. Email, Chat or Call Us for more details.
Add to Wish List
-
Tascam
Item# TCM-AK-DC16
Keep your Model 16 console safe from dust and dirt with this Tascam AK-DC16 durable cover. The included flap at the top allows you to protect your gear without ruining your cable setup.
Specifications: Dimensions: 450(W) x 95(H) x 480(D)mm / 17.7"(W) x 3.7"(H) x 18.9"(D)mm
Weight: 390g / 0.86lb

-
Tascam
Item# TCM-AK-DC24
Keep your Model 24 console safe from dust and dirt with this Tascam AK-DC24 durable cover. The included flap at the top allows you to protect your gear without ruining your cable setup.
Specifications: Dimensions: 600(W) x 110(H) x 548(D)mm / 23.6"(W) x 4.3"(H) x 21.6"(D)mm
Weight: 480g / 1.06lb

-
Tascam
Item# TCM-AK-RM16
Put your Model 16 console exactly where you need it with this sturdy Tascam AK-RM16 rack mount kit. The included rack mount ears and screws will help you ensure that your gear setup can handle a Model 16 console anywhere.
Specifications: Dimensions: 462(W) x 34(H) x 45(D)mm / 18.2"(W) x 1.3"(H) x 1.8"(D)mm
Weight: 0.9kg / 1.98lb (L-R pair)

-
-
Yamaha Commercial Audio
Item# YMH-TF5-COVER
This Yamaha dust cover (TF5-COVER) is for the Yamaha TF. This product will protect your TF5 against naturally occuring particals, such as dust.
Features: Protects against dust
Snug fit to your TF5
Specifications: 12L x 10.45W x 4.9H"
