-
Item# DFD-124-5
The Doug Fleenor 124 Design is a four output DMX splitter that also supports the RDM protocol. It is available with 3 pin XLR (model 124-3), 5 pin XLR (model 124-5), or RJ-45 connectors. Each output features its own driver circuit, insuring a problem on one output will not affect the other outputs. The four outputs share a common (pin 1s are tied together). The input is completely isolated from the outputs (there are no electrical connections between any of the input pins and any...

-
Item# DFD-PRE10-A
The Doug Fleenor Design PRE10-A Preset 10 Architectural is a lighting control station capable of storing up to ten presets. The PRE10-A offers "Radio Button" operation, where only one preset may be active at time. These presets are recorded by capturing the output of a DMX512 console. Each preset can then be assigned a unique fade time, from 0 to 999 seconds. Presets are recalled by pressing one of the buttons.
Systems can be created by using one or more stations and a power...

-
Item# DMXDECELERATORII
The DMX DECELERATOR II is a DMX512 isolator and re-timing device. It can receive any signal within the DMX512 specification and it can accept some signals outside of the specification. It produces a DMX output signal with "relaxed" timing characteristics which are required by some DMX receiving devices. In addition, a BYPASS mode is provided. When this mode is selected, the DMX DECELERATOR II copies the timing from the input signal to the isolated output directly with no changes. This...

-
Item# DFD-121-3
The Doug Fleenor Design 121-3 is a DMX splitter that is available in three standard configurations: three, five, or eleven outputs from a single DMX input. An enhanced five output splitter with miswiring and lightning protection, and a universal power supply is also available (see the model 125EE data sheet). Units with any number of inputs and outputs may be manufactured on a custom basis.
Each output is electrically isolated from the input, and from every other output, by 2500 volt optical...

-
Item# DFD-123-3
The Doug Fleenor Design Model 123 DMX splitter is available in three standard configurations: three, five, or eleven outputs from a single DMX input. An enhanced five output splitter with miswiring and lightning protection, and a universal power supply is also available (see the model 125EE data sheet). Units with any number of inputs and outputs may be manufactured on a custom basis.
Each output is electrically isolated from the input, and from every other output,...

-
Item# DFD-124-3
The Doug Fleenor Design, Inc. 124-3 is an economical bi-directional DMX512/RDM splitter. It is available with 3 pin (model 124-3) or 5 pin (model 124-5) XLR connectors for all DMX512/RDM connections, as well as RJ45 connectors (model 124-RJ) and terminal block connectors (model 124-TB). These splitters have fully isolated inputs. The four outputs are separately driven but are not isolated from one another. The rugged chassis made from 0.1" thick aluminum is designed for portable use. A +"...

-
Item# DFD-125-3
The Doug Fleenor Design 125-3 DMX splitter is available in three standard configurations: three, five, or eleven outputs from a single DMX input. An enhanced five output splitter with miswiring and lightning protection, and a universal power supply is also available (see the model 125EE data sheet). Units with any number of inputs and outputs may be manufactured on a custom basis. Each output is electrically isolated from the input, and from every other output, by 2500 volt optical couplers....

-
Item# DFD-125-5
The Doug Fleenor Design DMX512 125-5 Isolated Splitter / Amplifier is available in three standard configurations: 3, 5, or 11 outputs from a single DMX input. An enhanced five output splitter with protection from miswiring and lightning, and a universal power supply is also available (see model 125EE). Units with any number of inputs and outputs may be manufactured on a custom basis.
Each output is electrically isolated from the input, and every other output, by...

-
Item# DFD-125EE-5
The Doug Fleenor Design Enhanced Isolated Splitter 125EE-5 includes all the features of our standard models with added protection to meet the needs of harsh operating conditions. As with our standard splitters, all outputs are isolated from the input and from the other outputs by optical couplers. Every output has its own power supply and line driver. For protection against electrical storms, the 125EE adds four transient absorbers on the input, two on each output, and one on the...

-
Item# DFD-127-5
The Doug Fleenor Design 127-5 is a bi-directional DMX512/RDM splitter with 5 pin XLR connectors. Each of the eight ports is fully isolated, and bi-directional with optical isolation, fault protection to ±60V, and transient protection to ±15KV. The unit has a universal voltage power supply and uses slew-rate-limited output drivers. Slew-rate-limited drivers minimize EMI and reduce reflections caused by improperly terminated cables.
Note: This product uses a slew-rate-limited...

-
Item# DFD-COLORWHEEL
The Color Wheel is a simple wall-mounted device designed to operate DMX512 based LED lighting fixtures. It can be configured to operate 3, 4, or 5 channel fixtures. Active channels may be increased or decreased individually, or all at once.
Specifications: Controller Type: Manual, Wall Console
Controller Protocol: DMX-512DMX
Device Type: Wall Plate

-
Item# DFD-DMX12ANL-5
The Doug Fleenor Design DMX12ANL-5 and DMX12ANL-TB series are 12 channel DMX512 to analog 0-10V interfaces. They are available with either 5 pin XLR connectors or pluggable terminal blocks for the DMX512 in and thru connections. The analog outputs for both versions appear on pluggable terminal blocks. These units can be used as portable devices, or they can be rack mounted using optional rack kit model RK8-1.
Each analog output is capable of sourcing or sinking up to 15mA. No user adjustments...

-
Item# DFD-DMX12DIM-ELV
The Doug Fleenor Design DMX12DIM-ELV is a 12 channel, 100 Watt per channel dimmer pack. It is fed by a single 120VAC 15A branch circuit. Each of the dimmers can be separately controlled using a DMX512-based lighting controller.
The dimmers use MOSFET power devices. The dimmed outputs are Electronic Low Voltage(ELV) compatible using reverse phase (aka: trailing edge) control techniques. The DMX12DIM-ELV is housed in an enclosure suitable for portable use or for mounting in a standard...

-
Item# DFD-DMX1REL20A
Doug Fleenor Design makes a series of Relay Packs that are controlled by DMX512. The DMX1REL20A is a single channel unit, designed to switch up to a 20 amp line voltage load, and uses a 30 amp relay. The unit is provided with two 18" 12/3 SJ pigtails for line-in and switched line-out. Supplied with 15 amp parallel blade connectors as standard, the unit may be wired with higher rating connectors by special order or may be rewired by the customer. Unit operates on 100-208V 50/60Hz,...

-
Item# DFD-DMX1REL20A2P
The DMX1REL20A-2POLE controls two output legs using a single channel of DMX512. The relays can switch up to a 20 amp line voltage load and are built with a 30 amp relay for robust performance. The output is suitable for 208-240VAC with both the hot legs being switched. The unit is provided with two 18" 12/3 SJ pigtails for line in and switched line out. Supplied with 20 amp twist lock connectors (L6-20) as standard, the unit may be wired with different connectors by special order or may be...

-
Item# DFD-DMX6REL15A
Doug Fleenor Design makes a series of Relay Packs that are controlled by DMX512. These six channel units are designed to switch up to 15 amp line voltage loads and use 30 amp relays. Line voltage input is on an 18" 12/3 SJ pigtail(s) fitted with 15 amp parallel blade plug(s). Model DMX6REL15A has one line in pigtail. Model DMX6REL30A has two line in pigtails (one for channels 1-3, one for channels 4-6). Switched line outputs are on chassis mounted 15 amp parallel blade receptacles....

-
Item# DFD-DMX6REL30A
Doug Fleenor Design makes a series of Relay Packs that are controlled by DMX512. These six channel units are designed to switch up to 15 amp line voltage loads and use 30 amp relays. Line voltage input is on an 18" 12/3 SJ pigtail(s) fitted with 15 amp parallel blade plug(s). Model DMX6REL15A has one line in pigtail. Model DMX6REL30A has two line in pigtails (one for channels 1-3, one for channels 4-6). Switched line outputs are on chassis mounted 15 amp parallel blade receptacles....

-
Item# DFD-ES2
The Doug Fleenor Design ES2 is a stand-alone DMX snapshot recorder which can store two preset scenes or "looks". It can be used as a stand-alone main station or configured as a remote station in conjunction with another ES2 configured as a main station. It can be used as a remote station with Doug Fleenor Design’s Preset 10-A, Preset 10-A2, or Rerun stations.
In remote mode, the ES2 has two buttons which can be assigned to remotely trigger any of the presets/shows on a master station....

-
Item# DFD-GIZMO
The Doug Fleenor Design GIZMO can transmit, receive, save and playback scenes, and perform a variety of data and cable tests. It features a rugged 1/10" aluminum enclosure, a 16 character by 2 line back lit display, an optically isolated input, a slew-rate limited output, a NiMH rechargeable battery good for four hours of continuous testing, and a five year warranty. A nylon carrying case and AC adapter/charger are included. The full numeric keyboard provides direct channel access...

-
Item# DFD-PRE10-A-POPO
The Doug Fleenor Design PRE10A-POPO offers ten HTP presets. Each of these ten HTP presets are capable of being turned ON or OFF individually. Preset 10 Architectural is a lighting control station capable of storing up to ten presets. These presets are recorded by capturing the output of a DMX512 console. Each preset can then be assigned a unique fade time, from 0 to 999 seconds. Presets are recalled by pressing one of the buttons.
Systems can be created by using one or more stations...

-
Item# DFD-PRE10-A2
The Doug Fleenor Design Preset 10 Architectural Two is a further development of thier popular Preset 10 Architectural controller. The Preset 10 Architectural Two (PRE10A2) offers new features and different wiring options. The new features of the PRE10A2 include a grand master, pile on mode (input + preset), jumper selectable button modes (radio or push on/push off), face panel lockout, and a two gang form factor that allows PRE10A2 to fit in all two gang back boxes. The PRE10A2 has separate...

-
Item# DFD-PRE10-P
The Doug Fleenor Design Preset 10 Portable PRE10P can act as a backup for any DMX512 lighting console or as a stand-alone DMX512 preset console. The PRE10P is a DMX512 playback device that can take up to ten snapshots from a DMX console and play them back at the press of a button. Fade times can be set from 0 to 999 seconds (default is 2 seconds).
Each PRE10P can work in conjunction with a lighting console, automatically switching between preset and console control. When the console...

-
Item# DFD-PRE8-D
Doug Fleenor Design PRE8-D Preset 8 is a lighting control station that stores eight preset looks. Each look, or scene, has an associated slider that adjusts the intensity of that look. The looks are recorded into Preset 8 by capturing the output of any DMX512 console. The user or installer creates a look using their DMX512 console of choice, then presses the recessed record button on Preset 8, followed by moving the slider to be recorded. Often, presets are recorded only once, at the time...

-
Item# DFD-2322DMX-5
The Doug Fleenor 2322DMX RS-232 to DMX interface allows advanced A/V control systems and computers to operate standard DMX512 devices such as dimmers and moving lights. It can also be used to allow an RS-232 based control system to receive DMX512 data. The RS-232 protocol used for this communication is made up of simple ASCII strings sent or received at 9600 baud. The interface can set and fade DMX channels to specific levels. It can also record and play 20 presets, each with individual fade...
