Ashly Audio nXe4004 Network Power Amplifier 4 x 400 Watts @ 2 Ohms

NXE4004 - Overview

• Features:

  • Ethernet Control and monitoring of amplifier functions, with front panel COM activity LED
  • Serial data port for use with Ashly remote control devices, or optional RS- 232 converter for third party controllers (INA-1)
  • Use ProteaT Software to remotely disable all front panel controls, including the on/off switch, for a tamper-proof installation
  • Real-Time Clock with Event Scheduler
  • Instant Standby Mode 30% reduction in power consumption with on/off and Preset Recall, both via contact closure, software control, or event scheduler
  • Programmable power-on delay
  • Aux preamp outputs, and fault condition logic outputs
  • Optional Cobranet® or Dante® and AES3 digital audio input with pass thru
  • Rear panel DIP switches select low impedance (2, 4, and 8 Ohm), constant voltage (70V or 100V), high pass filter, limiter and input gain on each channel
  • Ashly Energy Management System (EMS) for increased efficiency) automatic <1Wsleep-mode (defeatable)
  • Switch mode power supply automatically detects 120V or 240V AC operation
  • Extensive protection circuitry
  • Continuously variable cooling fans
  • Front panel power switch and level controls (can be disabled for security)
  • Multiple internal power supplies provide increased channel separation and reliability
  • Remote DC level control on each input channel (2 RU models only)
  • Genuine Neutrik® connectors on 2 RU models for security, safety, and reliability
  • Safety / Compliance: cTUVus, CE, FCC, RoHS
   

• Specifications:

  • Voltage Gain: Selectable at 26dB, 32dB, 38dB, or 1.4V
  • Damping Factor: >250 (8 Ohms load <1kHz)
  • Input High Pass Filter: 80Hz 2nd order
  • Distortion (SMPTE, typical): <0.5%
  • Distortion (THD-N, typical): <0.5% (8 Ohms, 10dB below rated power, 20Hz-20kHz)
  • Channel Separation: -75dB (dB from full output, 1kHz)
  • Signal-to-Noise (20Hz-20kHz, unweighted): >114dB (all 3.0x models), >111dB (all 1.5x models), >108dB (all 800x models), >105dB (all 400x models)
  • Frequency Response: 20Hz-20kHz, +/-0.05dB
  • Balanced Input Connector: Euroblock 3.5mm, 1/4" TRS and XLR Combo jack
  • Input Impedance: 10k Ohms
  • Maximum Input Level: +21dBu
  • Speaker Output Connector: Neutrik® speakON®
  • Control Network: Compatible w/ standard 100MB Ethernet
  • AUX Output Connector: Balanced Euroblock 3.5mm
  • AUX Output Maximum: Level +21dBu
  • Remote Standby Contact Closure: Euroblock 3.5mm, close contact to GND for standby mode
  • Preset Recall Contact Closure: Euroblock 3.5mm, close contact to GND for preset 1-4 recall
  • Data Connection: Euroblock 3.5mm - Gnd, +18V, In, Out
  • Fault Condition Logic Outputs: Fault indicated by loss of 1Hz "heartbeat" pulse signal
  • Remote DC Level Control: Euroblock 3.5mm - Gnd, CV, V+ per input
  • Attenuators (per channel): Front panel, software, offset link group, and remote. Fully off = Mute
  • Amplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
  • Cooling: Continuously variable temperature controlled axial fan(s)
  • Environmental: 32° to 113°F (0° to 45°C) (non-condensing)
   

• GTIN:

  0694970892194