Audio Distribution Amplifiers

Viewing Item(s):

Display:

Viewing Item(s):

Display

Show As

Shure ANI4IN-XLR 4-Input - XLR Connectors - Mic/Line Dante Audio Network Interface with PEQ and Audio Summing
Shure Inc
Item# SH-ANI4IN-XLR
The Shure ANI4IN-XLR converts up to four line / mic analog signals onto a Dante network for easy audio routing and browser-based control. Features: Single Ethernet port carries Dante audio, power (PoE - class 0 / 3) LEDs indicate power, network and audio Provides control strings for third-party teleconferencing and AMX and Crestron 4 Band C/S PEQ on every channel Channel summing to combine input signals and send over a single Dante feed Browser based software control for all device...
Our Price: $686.00
Availability: In Stock
Add to Wish List
Cobalt ROYAL 9243 Analog Audio (Balanced) Distribution Amplifier openGear Card with Remote Gain Control
Cobalt Digital
Item# CB-ROYAL-9243
The Cobalt ROYAL 9243 Analog Audio Distribution Amplifier with Remote Gain Control is a broadcast-quality balanced analog audio DA with stereo 2x4, mono 1x8, and stereo sum L+R x 8 selectable output modes. Unlike most analog audio DAs, the 9243 electronic attenuators allow overall gain (stereo ganged) and per-channel trim (offset) via DashBoard remote control. The space-saving design and very low power consumption of the 9243 provides for high density, allowing two cards to be collocated...
Our Price: $595.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Rupert Neve Designs RNDI-8 1RU Eight Channel Active Transformer Direct Interface
Rupert Neve Designs
Item# RUP-RNDI-8
Legendary tone, unquestionable reliability. Eight channels of the superb-sounding RNDI in one rack space. With over 25,000 channels shipped since its launch in 2015, the RNDI is firmly established as the direct interface of choice for many of the world's most discerning musicians and engineers. Its custom transformers and discrete FET amplifiers deliver a vibrancy and clarity that captures the full harmonic depth of any source, and its unquestionable reliability has led to its adoption by...
Our Price: $1,999.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
RDL RCX-5C RCX Room Combining System Controller
Radio Design Labs
Item# RCX-5C
The system controller accommodates a maximum of 5 rooms, combined in any adjacent arrangement. Audio inputs from each room are Line only, MICLINE dynamic mic, MICLINE condenser mic. A front-panel level knob with LED metering is provided for each room input. MUSIC and PAGING inputs may feed each room if desired. Two RCX-5Cs may be linked in larger systems where two groups of rooms need to be combined. The standard RCX-5C does not mute mics in a room while listening to music. - Power Supply Included...
Our Price: $1,774.02
Availability: 2+ Weeks
Add to Wish List
RDL ST-DA3 Line Level Distribution Amplifier - 1x3
Radio Design Labs
Item# ST-DA3
The RDL ST-DA3 gives you the advantages of an audio distribution amplifier PLUS you can put it where you need it. The ST-DA3 allows bridging of any audio line, adjusting the gain, and driving up to three high or low impedance, balanced or unbalanced loads. The ST-DA3's wideband circuitry produces the unsurpassed pure clarity, low-distortion and low-noise for which RDL products are known. The ST-DA3 features RDL's SupplyFlex power input configuration. The module will operate directly from...
Our Price: $207.43
Availability: In Stock
Add to Wish List
Cobalt RM20-9243-B openGear Rear I/O Module - Standard Width - 2 Analog Audio In/8 Analog Audio Out - Balanced
Cobalt Digital
Item# CB-RM20-9243-B
The Cobalt Digital RM20-9243-B is a rear I/O Module (Standard Width) for the Cobalt Digital 9243 openGear card featuring (2) Balanced Analog Audio Inputs & (8) Balanced Analog Audio Outputs all onType: Phoenix type removable modular connectors. The 9243 Analog Audio Distribution Amplifier with Remote Gain Control is a broadcast-quality balanced analog audio DA with stereo 2x4, mono 1x8, and stereo sum L+R x 8 selectable output modes. Unlike most analog audio DAs, the 9243 electronic attenuators...
Our Price: $210.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Ross ADC-8434-A Quad Analog Audio to Dual AES Converter with up to 24-bit ADC
Ross Video
Item# ROSS-ADC-8434-A
The Ross ADC-8434-A quad analog audio to dual AES converter is a broadcast quality, modular solution, which converts 4 analog audio channels to 2, 24-bit, unbalanced AES3 signals. The ADC-8434-A accepts 4 analog audio signals (2 stereo pairs) and provides 2 copies of each of the 2 AES / EBU output signals. The ADC-8434-A also has internal audio processing with independent channel gain, master stereo gain, sum (mono), and left or right only selection. The conversion from analog to digital...
Our Price: $1,200.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DA6G 6 Way Stereo Distribution Amplifier With Output Gain Control
Sonifex
Item# SON-RB-DA6G
The RB-DA6G is a 1U rack-mount high performance 6 way stereo distribution amplifier for splitting a source into a number of different outputs. It is identical to the RB-DA6 with the addition of individual output gain adjustment, instead of global stereo gain adjustment. Specifications: Audio Specification Maximum Input Level: +28dBu Maximum Output Level: +28dBu Frequency Response: 20Hz to 20kHz ñ0.1dB (600O load, ref 1kHz) Gain Range: Adjustable 8dB loss to 18dB gain...
Our Price: $851.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DA6 Stereo Distribution Amplifier
Sonifex
Item# SON-RB-DA6
The RB-DA6 is a 1U rack-mount high performance 6 way stereo distribution amplifier for splitting a source into a number of different outputs. The RB-DA6 has 1 stereo input and 6 stereo outputs. It can also be configured so that 1 mono input can be distributed to 12 outputs by use of a switch which is recessed on the front panel to prevent it being accidentally knocked. The XLR-3 inputs and outputs are electronically balanced and can be wired unbalanced. Each output is individually buffered so...
Our Price: $802.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
ESE ES-246/BNC Quad 1x6 SMPTE-LTC/IRIG Distribution Amplifier - BNC Option
ESE
Item# ES-246-BNC
The ES-246/BNC is a Quad 1 x 6 SMPTE-LTC / IRIG Time Code Distribution Amplifier. It is housed in a 1.75" x 19" rackmount panel and chassis (the chassis extends 4.8" behind the panel). Each amplifier provides a loop-thru input and six 600 ohm outputs. The inputs and outputs are connected via the rear mounted BNC connectors. The ES-246/BNC is a transformerless design that takes a single unbalanced input and provides six unbalanced single ended outputs. The output levels for each of the four inputs...
Our Price: $598.50
Availability: 2+ Weeks
Add to Wish List
MultiDyne MDoG-6001-DA-2x4-AA 1x8/2x4 openGear Analog Audio Distribution Amplifier Card
Multidyne
Item# MDOG-6001-DA-2X4
The MultiDyne MDoG-6001-DA-2X4-AA openGear card is a remote gain analog audio distribution amplifier designed for broadcast use. It can be used as either a mono 1x8 or dual-channel 1x4 stereo audio distribution amplifier. When used with the standard rear module, it provides 8 copies of the single mono input signal or 4 copies each of the stereo inputs. The MDoG-6001-DA-2X4-AA has internal audio processing for independent channel or stereo gain control as well as summing capability...
Our Price: $500.74
Availability: Usually Ships in 5-14 Days
Add to Wish List
Henry Engineering DDA AES Digital DA 2X4 Zero-Delay AES Distribution System
Henry Engineering
Item# HE-AESDIGDA2X4
The Henry Engineering AES Digital DA 2X4 is a distribution system for digital audio signals. It can accept either an AES or S/PDIF digital audio stream, and create four identical AES outputs. The AES DA is 100% bit-accurate and transparent to the source, adding absolutely no delay or latency to the signal. The AES input and all four AES outputs are individually transformer balanced and isolated from ground. The S/PDIF input signal is converted to an AES standard level and source impedance....
Our Price: $395.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Rolls RA163 8 Channel XLR Distribution Amp with Channel Attenuation
Rolls Corporation
Item# RA163
The Rolls RA163 is an eight channel distribution amp. It has independent volume attenuation for each channel, and 1X8(mono) or 2X4(stereo) compatibility. Balanced XLR jacks for all inputs and outputs. The RA163 also has volume knobs on the front panel and access to the stereo/mono switch. The chassis is made of powder coated steel and uses an IEC 120V power cord, no wall wort adapter with this professional grade distribution amp. Designed for installations where you need to send...
Our Price: $199.00
Availability: In Stock
Add to Wish List
Multidyne R2-6001-DA-2x4-AA openGear 20-Slot Frame Rear I/O Module for MDoG-6001-DA-2x4-AA
Multidyne
Item# R2-6001-DA-2X4
The MDoG-6001-DA-2X4-AA is also ideal for LTC timecode distribution throughout a facility. In the 1x8 mode, the MDoG-6001-DA-2X4-AA provides 8 copies of the incoming signal when used with the R2-6001-DA-2x4-AA full rear module. The MDoG-6001-DA-2X4-AA is a remote gain analog audio distribution amplifier designed for broadcast use. It can be used as either a mono 1x8 or dual-channel 1x4 stereo audio distribution amplifier. When used with the standard rear module, it provides 8 copies of...
Our Price: $149.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL TX-A2 Balanced to Unbalanced Audio Converter
Radio Design Labs
Item# RDL-TX-A2
The TX-A2 is the ideal choice in installations requiring passive isolation and level attenuation between a professional balanced line-level mono source and consumer equipment unbalanced inputs. The TX-A2 is a complete unbalanced line-level audio output module. The front panel provides a detachable terminal block for connection of a balanced +4 dBu audio source. The input signal is coupled to two front-panel gold plated RCA jacks through a studio-quality isolation transformer. Each output is coupled...
Our Price: $130.11
Availability: In Stock
Add to Wish List
Toslink 4-Output Optical Distribution Amplifier/Repeater
Inday
Item# TLDA-1
Toslink 4-Output Optical Distribution Amplifier/Repeater Features: Toslink Digital Audio Splitter Converts One Toslink input to Four isolated Toslink outputs. Each output has its own Fiber Optic Transmitter. NO signal degradation. NOT a "Reflective" splitter that attenuates the signal. 96/192kHz Digital Audio compatible (12.288Mb/s). ADAT compatible! Power Supply Included Made in Oregon,USA!
Our Price: $54.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Shure ANI22-XLR Dante Audio Network Interface with Analog Audio XLR Connectors
Shure Inc
Item# SH-ANI22-XLR
The Shure ANI22 can bring up to two line / mic signals onto or from a Dante network for easy audio routing and convenient browser-based remote control. Works with Microflex® Advance™ and Microflex® Wireless. Two versions available: ANI22BLOCK with analog audio block connectors (2 in, 2 out) and ANI22XLR with analog audio XLR connectors (2 in, 2 out). Features: Converts up to 2 mic / line analog signals onto a Dante Network Converts up to 2 Dante digital audio...
Our Price: $686.00
Availability: In Stock
Add to Wish List
Cobalt RM20-9917-A 20-Slot openGear Frame Rear I/O Module - Two 12G-SDI/ASI/MADI Inputs / Eight 12G-SDI/ASI/MADI Output
Cobalt Digital
Item# CB-RM20-9917-A
The Cobalt RM20-9917-A is the rear module option for the Royal 9917-DA-12G-1x8/2x4 openGear card only. It features two 12G/6G/3G/HD/SD-SDI/ASI/MADI Inputs and eight 12G/6G/3G/HD/SD-SDI/ASI/MADI outputs. Specifications: Power: 3 Watts 12G/6G/3G/HD/SD-SDI Inputs Number of Inputs: 2 Standard: SMPTE 424M, 292M, and 259M Return Loss: - >15 dB at 5 MHz - 1.485 GHz - >10 dB at 1.5 GHz to 3 GHz 12G/6G/3G/HD/SD-SDI Output Number of outputs:...
Our Price: $195.00
Availability: In Stock
Add to Wish List
Shure ANI4OUT-XLR 4-Output - XLR Connectors - Mic/Line Dante Audio Network Interface with PEQ and Audio Summing
Shure Inc
Item# SH-ANI4OUT-XLR
The Shure ANI4OUT-XLR converts a Dante digital audio signal to four discrete line/mic analog signals. Features: Single Ethernet port carries Dante audio, power (PoE - class 0 / 3) LEDs indicate power, network and audio 4 Band C/S PEQ on every channel Browser based software control for all device parameters, per input channel: - Pre-amp gain - Mute control - Digital gain - Polarity control Specifications:
Our Price: $686.00
Availability: In Stock
Add to Wish List
Cobalt Royal 9917-DA-1x8/2x4-12G Dual-Channel 12G/6G/3G/HD/SD Reclocking Distribution Amplifier
Cobalt Digital
Item# CB-ROYAL-9917DA
The Cobalt Royal 9917-DA-12G-1x8/2x4 Dual-Channel 12G/6G/3G/HD/SD Reclocking Distribution Amplifier is a two-channel, multi-rate SDI distribution amplifier capable of equalizing and reclocking 12G, 6G, 3G, HD, and SD signals. Excellent receiver EQ performance allows for up to 160m cable lengths for HD signals. The Royal 9917-DA-12G-1x8/2x4 can be set up as either a single-channel 1:8, dual-channel 1:4, or 1:8 with failsafe using DashBoard™ remote control software or card-edge...
Our Price: $695.00
Availability: In Stock
Add to Wish List
Rolls RA63b 8-Channel Mono 4 Channel Stereo Distribution Amplifier
Rolls Corporation
Item# RLS-RA63B
The Rolls RA63b is an eight channel mono, or four channel stereo distribution amplifier designed for the contractor / install market. The outputs are designed to drive high-level balanced lines in a sound distribution system. The screw terminals on the rear panel are for input and output, and each output may power more than one line. Features: Mono or Stereo Operation - mono input to eight outputs, or stereo inputs to four stereo outputs. +20 dB Gain switch. Screw Terminal inputs...
Our Price: $249.00
Availability: In Stock
Add to Wish List
Shure ANI22-BLOCK Dante Audio Network Interface with Analog Audio Block Connectors
Shure Inc
Item# SH-ANI22-BLOCK
The Shure ANI22 can bring up to two line / mic signals onto or from a Dante network for easy audio routing and convenient browser-based remote control. Works with Microflex® Advance™ and Microflex® Wireless. Two versions available: ANI22BLOCK with analog audio block connectors (2 in, 2 out) and ANI22XLR with analog audio XLR connectors (2 in, 2 out). Features: Converts up to 2 mic / line analog signals onto a Dante Network Converts up to 2 Dante digital...
Our Price: $686.00
Availability: In Stock
Add to Wish List
SoundTools CBFMX CAT Box Stage Box with Parallel for Daisy-Chaining - 2 Female XLRs (Inputs) + 2 Male XLRs (Outputs)
SoundTools
Item# RSS-CBFMX
Introducing the SoundTools CAT Box FMX CBFMX, revolutionizing your audio connectivity. This unit allows you send and receive analog mic or line level, AES3, DMX and/or COM down a shielded Cat5e, Cat6, or Cat7 cable. Simplify Your Stage Optimize your cabling system with the compact and durable SoundTools CAT Box featuring send and return lines. Minimize the number of cables required by running up to four channels of analog audio, DMX, AES3 or COM lines through a single...
Our Price: $130.00
Availability: In Stock
Add to Wish List
Stewart Audio DPA-220 PowerCore Audio Amplifier with PoE and External DC Supply Support
Stewart Audio, Inc.
Item# STW-DPA-220
The Stewart Audio PowerCore DPA-220 is a rugged and compact Dante enabled PoE high-performance audio amplifier that delivers up to 20W into a pair of 4-8Ω speakers or 40W into a single 4-8Ω speaker Elevate Every Sound Experience The PowerCore DPA-220 amplifier with Dante Embedded Platform (DEP) technology sets a new standard for performance, size, durability and features - from one of the industry's most trusted brands. PowerCore amplifiers are POE rated devices that...
Our Price: $594.00
Availability: In Stock
Add to Wish List
Angry Audio DISTRIBUTION GADGET 2x4 Stereo or 1x8 Monaural Analog Audio Distribution Amp - 115VAC
Angry Audio
Item# AA-DISTRIBUTION
Need to feed a stack of stuff from a single source? You could try the daisy-chain, but you may end up with a ground loop, signal degradation or worse. What you really need to get a signal to multiple destinations is a broadcast-grade distribution amplifier. Angry Audio poured some fresh ideas into the DA and called it, of course, the Distribution Gadget. The Distribution Gadget allows a single source to drive multiple destinations. This is especially useful in broadcasting for connecting...
Our Price: $379.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
Ashly Audio 24.24M Output - 4-Output Expansion Module for Protea 24.24M Matrix Processor
Ashly Audio
Item# ASH-2424M-OUT
The 24.24M Output from Ashley is a four-output expansion module for the Protea 24.24M Matrix Processor base unit. Each card provides an additional four channels of output and brings with it dedicated DSP and digital-to-analog converters. The card is field installable and require no additional programming from the base unit. Up to five output cards can be installed for a total of twenty-four outputs. Because of the on-board DSP, the base unit's processing is not impacted by the...
Our Price: $449.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
ATI ADA 206-XLR Dual 1x3 Low Noise Analog Audio Distribution Amplifier - XLR Connectors
ATI
Item# ATI-ADA-206-XLR
The DA206 is ideal for every application and every budget. Avoid RF and hum pick-up problems from noisy, lossy splitters. Prevent hard-to-find shorts from multiple taps on critical lines. Boost console outputs. Drive long lines. Eliminate rolloffs and distortion from mismatched load impedances and enjoy the maximum versatility that this unit provides. The DA206 gives you two inputs, each driving a master input gain adjustment and three individual output level trimmers. All outputs...
Our Price: $1,974.50
Availability: Usually Ships in 5-14 Days
Add to Wish List
ATI ADA 416-PHX Quad 1x4 Low Noise Analog Distribution Amplifier- Phoenix Connectors
ATI
Item# ATI-ADA-416-PHX
The ATI ADA416-PHX is an amplifier capable of routing audio to four distribution amplifier channels, all via balanced Phoenix inputs and outputs. The unit provides a master gain adjustment control for each channel, while individual trimmers are on hand for each output to accommodate gears of various sensitivities over its 20 dB range. Use it to distribute audio in offices, nightclubs, and more. You're sure to get a low-noise, strong-signal operation out of the unit, as it's RF protected...
Our Price: $2,744.50
Availability: In Stock - Ships Factory Direct
Add to Wish List
ATI SUM100-3 2 to 1 Channel Summing Audio Amplifier - XLR and RCA I/O
ATI
Item# ATI-SUM100-3
The ATI SUM100 Summing Amplifier is an inexpensive, high performance amplifier that is designed as a line level stereo to mono summing amplifier. It is also useful as a gain block, and as an impedance converter and summing for IHF (RCA type) signals. The inputs provide balanced 40Kohm bridging impedance for line levels up to +24dBm. The high input impedance allows the SUM100 inputs to also bridge -10dBu (hi-fi, RCA plug) lines without loading. Front panel, screwdriver adjust, full...
Our Price: $874.50
Availability: Usually Ships in 5-14 Days
Add to Wish List
Atlas IED Atmosphere X-ANS Ambient Noise Sensor
AtlasIED
Item# ATL-X-ANS
AtlasIED's Atmosphere 2.0 Audio Control System sets a new standard for digital audio with multi-zone processors, amplifiers, and a variety of accessories. Touchless control, easy-to-program automation, and artificial intelligence offer integrators and users an effortless way to create the perfect Atmosphere for any business! The Atmosphere X-ANS is an ambient noise sensor specifically for use with the Ambient Noise Compensation (ANC) functionality in the Atmosphere AZM....
Our Price: $247.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Atlas IED Atmosphere A-BT Remote Bluetooth Audio Input
AtlasIED
Item# ATL-A-BT
AtlasIED's Atmosphere 2.0 Audio Control System sets a new standard for digital audio with multi-zone processors, amplifiers, and a variety of accessories. Touchless control, easy-to-program automation, and artificial intelligence offer integrators and users an effortless way to create the perfect Atmosphere for any business! The Atmosphere A-BT is a remote Bluetooth™ audio input for the Atmosphere AZM audio processor. This expansion allows the Bluetooth™ receiver...
Our Price: $325.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Atlas IED Atmosphere A-RCA RCA/3.5mm Audio Input
AtlasIED
Item# ATL-A-RCA
Atlas IED's Atmosphere 2.0 Audio Control System sets a new standard for digital audio with multi-zone processors, amplifiers, and a variety of accessories. Touchless control, easy-to-program automation, and artificial intelligence offer integrators and users an effortless way to create the perfect Atmosphere for any business! The Atmosphere A-BT is a remote Bluetooth™ audio input (mono) for the Atmosphere AZM audio processor. This expansion allows the...
Our Price: $236.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Atlas IED Atmosphere A-XLR Remote XLR Audio Input
AtlasIED
Item# ATL-A-XLR
AtlasIED's Atmosphere 2.0 Audio Control System sets a new standard for digital audio with multi-zone processors, amplifiers, and a variety of accessories. Touchless control, easy-to-program automation, and artificial intelligence offer integrators and users an effortless way to create the perfect Atmosphere for any business! The Atlas IED Atmosphere A-XLR is a remote XLR audio input for the Atmosphere AZM audio processor. This expansion acts identically to the on-board...
Our Price: $277.99
Availability: 2+ Weeks
Add to Wish List
Atlas IED TSD Series DA28 2 x 8 Audio Line Distribution Amplifier - Black
AtlasIED
Item# ATL-TSD-DA28
Atlas Sound Time Saving Devices are designed to solve some of the common audio system problems in the easiest and in the most efficient and cost-effective way. Utilizing the highest quality components and inspired by real world installation issues, the Atlas Sound TSDs include mixers, amplifiers, preamps, and other distribution and control devices to simplify your connections, provide specific application needs, and add flexibility in expansion and changes that prevent expensive system overhauls The...
Our Price: $349.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Attero Tech Synapse D16Mio 16x16 Channel Mic/Line I/O Dante/AES67 Audio Interface 1RU
Attero Tech
Item# SYNAPSED16MIO
The Attero Tech D16Mio is a high performance, high channel density networked audio interface supporting Dante™ with AES67 interoperability. The D16Mio features 16 channels of studio grade microphone preamplifiers using THATCorporation mic preamp technology, with up to 51 dB of digitally controlled gain in 3 dB steps. Each mic input also supports P48 switchable phantom power and a switchable pad accommodation of pro line level inputs. The balanced line level outputs feature digitally...
Our Price: $5,380.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
AuviTran AVDT-BOB-ADE8IO Dante Breakout Box with AES/EBU & DSP
AuviTran
Item# AUT-AVDTBOBADE8I
The AuviTran AVDT-BOB is a compact Dante break out box with embedded Digital Signal Processing. The AVDT-BOB has state-of-the-art analog microphone preamplifiers for a very high audio dynamic and quality over Dante at a very contained price. The AVDT-BOB has a DSP to process and mix audio signal at the source and at the output. The AVDT-BOB features a dual core ARM processor associated with a large amount of flash memory for a universal and multiplatform remote control over IP...
Our Price: $1,629.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
Aviom Aviom16/o-Y1 A-Net Output Card for Yamaha Digital Products
Aviom
Item# AVIOM16O-Y1
The Aviom16/o-Y1 A-Net Card eliminates the need for an analog input module when creating a monitor mixing or audio distribution system, providing a direct digital interface between Yamaha digital products and Aviom's Pro16r Series, including the A-16II and A-16R Personal Mixers, A-Net distributors, and output modules. Yamaha Product Compatibility The Y1 card fits into any available MY expansion slot and is compatible with all Yamaha consoles and mix engines that support the...
Our Price: $899.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Aviom D400 A-Net Distributor with Dante Interface
Aviom
Item# AVM-D400-DANTE
The D400 and D400-Dante A-Net Distributors provide the link between the personal mixing system's inputs and the Personal Mixers, providing power and a copy of the digital audio stream to your Aviom Personal Mixers, utilizing standard Cat-5e cables. The standard D400 has an A-Net input, perfect for using with analog input modules or digital console cards from Aviom or our third party partners. The D400-Dante has a Dante input instead, and allows up to 32 channels to be routed from a Dante-enabled...
Our Price: $1,399.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Aviom D800-Dante V.2 2RU A-Net Distributor with A-Net Bridge Input and Dante Interface
Aviom
Item# AVM-D800-DANTEV2
The Aviom D800-Dante V.2 A-Net Distributors provide the link between the Dante network, input module, or console card and the Personal Mixers, providing DC power and the digital A-Net audio data stream to your Aviom Personal Mixers, utilizing standard Cat-5 cables. The A-Net and Dante versions of the D800 also integrate additional advanced options for delivering high-channel-count audio streams to your Personal Mixers, streamlining connections between A640 and A360 Personal Mixers...
Our Price: $3,399.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Cobalt Digital RM20-9257-A openGear Rear I/O Module 1 MADI Input BNC - 9 MADI Output BNCs For Use w/ The 9257 Card
Cobalt Digital
Item# CB-RM20-9257-A
Rear I/O Module for the Cobalt Digital 9257 1x9 MADI Audio Distribution Amplifier card.Single channel MADI in with 9 MADI outputs all on standard BNC coax connectors. The 9257 1x9 MADI Audio Distribution Amplifier provides an award-winning card-based solution for distribution of AES10 MADI signals. The card supports sampling frequencies up to 96 kHz, with a 64-channel payload supported at the industry standard 48 kHz sampling rate (all other sampling rates specified as valid per...
Our Price: $113.60
Availability: Usually Ships in 5-14 Days
Add to Wish List
Cobalt Digital RM20-9257-B/S-HDBNC 20 Slot Frame Rear I/O Module (Split - Supports 2 Cards) 1 MADI Input - 9 MADI Output
Cobalt Digital
Item# CB-RM20-9257-B
Cobalt Digital RM20-9257-B/S-HDBNC is a 20-Slot Frame Rear I/O Module with (Split) Dual MADI Input (HD-BNC), 9 MADI Outputs (HD-BNC) per card.
Our Price: $298.99
Availability: In Stock - Ships Factory Direct
Add to Wish List
Cobalt RM20-9243-D/S Rear I/O openGear Module for 9243 - Split - Dual 1x4 Balanced Analog Audio I/O
Cobalt Digital
Item# CB-RM20-9243-D-S
The Cobalt Digital RM20-9243-D-S is a rear I/O Module (Split) Dual 1x4 Balanced Analog Audio I/O (connections are per card) w/ Phoenix type removable modular connectors. The 9243 Analog Audio Distribution Amplifier with Remote Gain Control is a broadcast-quality balanced analog audio DA with stereo 2x4, mono 1x8, and stereo sum L+R x 8 selectable output modes. Unlike most analog audio DAs, the 9243 electronic attenuators allow overall gain (stereo ganged) and per-channel trim (offset)...
Our Price: $225.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Cobalt RM20-9262-B 20-Slot Frame Rear I/O Module (Standard Width) for Cobalt 9262
Cobalt Digital
Item# CB-RM20-9262-B
The Cobalt RM20-9262-B is a rear module option for the 9262 openGear card ONLY! It is a 20-Slot Frame Rear I/O Module (Standard Width). It has 1 AES Input BNC, 4 AES Reclocked Output BNCs, and 4 Analog Audio Outputs. Features: AES In AES Out (1x4 DA) Balanced Analog Audio Out (L) Balanced Analog Audio Out (R) (All coaxial connectors BNC)
Our Price: $148.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
Cobalt RM20-9262-B/S 20-Slot openGear Frame Rear I/O Module (Split Supports 2 Cards) 1 AES Input 2 AES Outputs 2 Analog
Cobalt Digital
Item# CB-RM20-9262-BS
The RM20-9262-B/S is a rear module option for the 9262 openGear card ONLY! It features digital-to-analog audio conversion as well as provides 1x4 AES/EBU DA. It supports audio sampling frequencies from 30 kHz to 192 kHz, and converts the incoming AES digital audio signal to a stereo balanced analog audio signal pair using 24-bit conversion. Cable equalization and reclocking techniques enable the 9262 to reliably recover incoming digital audio signals over large cable lengths. Features: 24-bit...
Our Price: $143.01
Availability: Usually Ships in 5-14 Days
Add to Wish List
DJ Pre II - Phono/Audio Recording System Interface
ART
Item# ART-DJPRE2
The DJ PRE II (formerly named the "Phono MicroPRE") acts as an interface between your turntable and your audio recording / playback system. The analog input capacitance can be switched between 100pF and 200pF to optimize your phono cartridge response. A switchable low cut filter removes turntable rumble while leaving the audio pristine. The front gain trim control and signal/clip LED allow you to optimize the preamp's gain for a wide range of input sources. The built-in low noise phono preamp circuitry...
Our Price: $74.99
Availability: 2+ Weeks
Add to Wish List
Drawmer DA6 1RU 6 Channel Stereo/12 Channel Mono XLR Balanced Audio Distribution Rackmount Amplifier with Monitoring
Drawmer
Item# DA-6
The Drawmer DA-6 is a six channel stereo (or twelve channel mono) distribution amplifier featuring XLR balanced inputs and outputs with optional transformer balancing where remote amplifiers and recorders are fed from separate power supplies. Designed to distribute mono and stereo balanced audio signals from a single source to multiple destinations the Drawmer DA-6 is perfect for multi-zone sound reinforcement installations, live sports events coverage, broadcast studios, video suites,...

Our Price: $1,089.00
Availability: 2+ Weeks
Add to Wish List
Ensemble Designs BrightEye 33 Analog Audio Distribution Amplifier
Ensemble Designs
Item# ENDE-BE33
BrightEye 33 is a high performance audio distribution amplifier for the broadcast and recording industry. Exceptional performance features include excellent response, noise and distortion specifications. BrightEye 33 functions with either 8 mono outputs or 4 stereo outputs. Additionally, BrightEye 33 can be used to distribute LTC. Gain adjustments are accessed from the front panel. This is a simple device with no USB port and no interface to BrightEye Mac or PC software. Power supply...
Our Price: $342.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
ESE ES 246 Quad 1x6 Rack Mount Audio Distribution Amplifier with XLR Option - 110-120 VAC
ESE
Item# ES-246-XLR
The ESE ES-246-XLR is a Quad 1x6 Audio Distribution Amplifier that accepts a balanced or unbalanced audio signal and produces exact copies of that signal. The outputs are isolated and have recessed gain controls. This unit is the ES 246 with Option XLR, all inputs and outputs are on XLR connectors for easy disconnect/reconnect. Features: 4 independent isolated amplifiers, each with six outputs XLR Input & Output Variable Gain, front panel adjustable for each amplifier,...
Our Price: $765.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
ESE ES 246/XLR/J Quad 1x6 Audio Distribution Amplifier with XLR Connectors - 220 VAC 50Hz
ESE
Item# ESE-ES-246-XLR-J
The ES 246/XLR/J is an ES-246 Audio Distribution Amplifier with XLR Connectors and the 220 VAC/50 Hz Operation option. This unit that accepts a balanced or unbalanced audio signal and produces exact copies of that signal. The outputs are isolated and have recessed gain controls. All inputs and outputs are accessible on terminal blocks for simple "permanent" installations. Or, if option "XLR" is specified, all inputs and outputs are available on XLR connectors for easy disconnect/reconnect....
Our Price: $801.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
ESE ES-217 Audio Distribution Amplifier Terminal Blocks
ESE
Item# ES 217
Amplifiers that accept a balanced or unbalanced audio signal and produce exact copies of that signal. The outputs are isolated and have recessed Gain controls. All inputs and outputs are accessible on terminal blocks for simple "permanent" installations. Or, if option "XLR" is specified, all inputs and outputs are available on XLR connectors for easy disconnect/reconnect. The ES-217 is an Audio DA with four independently adjustable (via the top-mounted Gain controls) outputs,while the ES-218*...
Our Price: $220.50
Availability: 2+ Weeks
Add to Wish List
ESE ES-217 Audio Distribution Amplifier with XLR Option
ESE
Item# ES-217XLR
The ESE ES-217XLR is an Audio Distribution Amplifier that accepts a balanced or unbalanced audio signal and produces four exact copies of that signal. The outputs are isolated and have recessed Gain controls. All inputs and outputs are available on XLR connectors for easy disconnect/reconnect. The terminal blocks are replaced with XLR connectors (the enclosure is doubled in height). Features: 4 isolated outputs Terminal Block or XLR version available Balanced or Unbalanced connections...
Our Price: $342.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
ESE ES-243 Quad 1 x 6 IRIG Distribution Amplifier
ESE
Item# ES 243
The ES-243 is designed to accept any IRIG time code (in its "pulse width coded" form) or any ESE Time Code signal (TC76, TC89 or TC90) and output up to 24 identical copies. The unit has four separate and isolated channels, each with six available outputs. Inputs and outputs are accessible on rear-mounted BNC connectors. Each of the four channels has a loop-thru input that allows the input signal to be "looped" from one channel into the next, so that up to 24 identical copies can be created. Each...
Our Price: $625.50
Availability: 2+ Weeks
Add to Wish List
ESE ES-245 Quad 1x6 SMPTE/EBU DA
ESE
Item# ES 245
The ESE ES-245 is a Distribution Amplifier designed to distribute and isolate most any audio signal including SMPTE and EBU time code. Four channels, each with six outputs, provide up to 24 identical copies. Inputs and outputs are available on the rear mounted terminal blocks (optional XLR connectors are available). The unit is rack mounted. Since the early '80s, ESE's Audio and Video Distribution Amplifiers have been recognized for their broadcast quality and durability. Using very similar...
Our Price: $625.50
Availability: 2+ Weeks
Add to Wish List
ESE ES-245J Quad 1 x 6 Audio Distribution Amp with 24 Independent Gain Controls and Isolated Outputs
ESE
Item# ESE-ES-245J
The ES-245J is an Audio Distribution Amplifier that accepts a balanced or unbalanced audio signal and produces exact copies of that signal. The outputs are isolated and have recessed Gain controls. All inputs and outputs are accessible on terminal blocks for simple "permanent" installations. Or, if option "XLR" is specified, all inputs and outputs are available on XLR connectors for easy disconnect/reconnect. This unit comes with option J which is configured to...
Our Price: $661.50
Availability: Usually Ships in 5-14 Days
Add to Wish List
ESE Quad 1x6 Rack Mount Audio Distribution Amplifier
ESE
Item# ES-246
The ES-246 is a quad 6-output Audio DA with 24 independently adjustable (via the front-mounted Gain controls) outputs, while the ES-246 has four Gain controls (one per input channel). The unit is a transformerless design and each of the four channels accepts a balanced or unbalanced audio signal that provides six exact copies. If unbalanced outputs are desired, up to twelve separate and isolated feeds can be made per channel. An input termination switch (between 600. and 100K.) is also provided...
Our Price: $445.50
Availability: In Stock - Ships Factory Direct
Add to Wish List
Evertz 400ADA-AUD 1x9 Analog Audio Distribution Amplifier Module for 3RU Exponent 400FR Frame
Evertz
Item# EVZ-400ADA-AUD
The Evertz 400ADA-AUD is an analog audio distribution amplifier designed as a general-purpose 1x9 amplifier for distributing balanced analog audio signals. The 400ADA-AUD can be operated with either differential or single ended inputs and offers a wide range of gain adjustment to handle a wide variety of input signals. It can also be housed in the 3RU Exponent 400FR frame that can hold up to 16 modules. Features: Differential and single ended input (automatic single ended to...
Our Price: $345.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
Genelec 9301B Multi-Channel Interface for 7300 Subwoofers - Expands Number of AES/EBU Channels
Genelec
Item# GNC-9301B
The 9301B multichannel interface is a handy digital I/O expansion that offers a simple and robust way to connect and integrate 7300 Series Smart Active Subwoofers as part of any Genelec immersive audio system. The 9301B works by providing seamless multichannel digital audio connectivity to the subwoofer's single digital AES/EBU XLR input/output. By installing this interface in the signal path, you'll gain 16 flawless digital channels for use with popular formats such as 9.1.6. You can also boost...
Our Price: $1,050.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley ADA-1023 Dual Stereo Analog DA For Densite 2 frame
Grass Valley
Item# GVLY-ADA-1023
The ADA-1023 is an analog audio DA that can be configured for single or dual channel (stereo) operation. In single channel mode, eight outputs can be driven while in dual channel mode, each channel has four outputs. A wide range of level gain control is possible and controlled from the card edge. A signal status is also available indicating the input signal(s) presence. Features: Single or dual analog audio input(s) Single channel 8-output or dual channel (stereo) 4-output Balanced inputs and...
Our Price: $489.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley ADA-1023-DRP Stereo Analog Audio DA Dual Rear Module for ADA-1023 Densite 2 Card
Grass Valley
Item# GVLY-ADA1023DRP
The Grass Valley ADA-1023-DRP is a stereo analog audio DA Dual Rear Module for ADA-1023 Densite 2 Card (sold separately). This rear I/O module is required to be used with the ADA-1023 card, it fits 2RU Densite frames only! The ADA-1023 is an analog audio DA that can be configured for single or dual channel (stereo) operation. In single channel mode, eight outputs can be driven while in dual channel mode, each channel has four outputs. A wide range of level gain control is...
Our Price: $168.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley DDA-1113 75 Ohm AES DA Card for Densite 2 Frame
Grass Valley
Item# MIR-DDA-1113
The Grass Valley DDA-1113 is a digital audio DA that supports AES-3id 75 ohm digital audio standard and provides 9 outputs. The input features clock regeneration for reduced jitter and signal restoration. An audio input signal status is also available indicating the input signal presence and validity with remote reporting. *The DDA-1113 does not include the required rear panel. Sold separately. Features: AES-3id audio unbalanced input 9 AES-3id audio outputs Remote control of carrier...
Our Price: $555.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley DDA-1113-3RU 75 Ohm AES DA for Densite 3 Frame Including 3RU Adapter
Grass Valley
Item# MIR-DDA-1113-3RU
The DDA-1113 from Grass Valley is a digital audio DA that supports AES-3id 75Ω digital audio standards and provides nine outputs. The input features clock regeneration for reduced jitter and signal restoration. An audio input signal status is also available indicating the input signal presence and validity with remote reporting. Features: AES-3id audio unbalanced input Nine AES-3id audio outputs Remote control of carrier quality Signal regeneration Silence detect with...
Our Price: $575.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley DDA-1113-3SRP Single Rear Connector Panel - Densite 3 Frame
Grass Valley
Item# MIR-DDA-11133SRP
Single Rear Connector Panel. The DDA-1113 is a digital audio DA that supports AES-3id 75 ohm digital audio standard and provides nine outputs. The input features clock regeneration for reduced jitter and signal restoration. An audio input signal status is also available indicating the input signal presence and validity with remote reporting.
Our Price: $178.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley DDA-1113-DRP Double Rear Connector Module Panel 1x9 For DDA-1113 Card
Grass Valley
Item# MIR-DDA-113-DRP
Double Rear Connector Panel (1x9). The DDA-1113 is a digital audio DA that supports AES-3id 75 ohm digital audio standard and provides nine outputs. The input features clock regeneration for reduced jitter and signal restoration. An audio input signal status is also available indicating the input signal presence and validity with remote reporting.
Our Price: $178.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Grass Valley DDA-1113-DRP Single Rear Connector Panel 1x4
Grass Valley
Item# MIR-DDA-113-SRP
Single Rear Connector Panel (1x4). The DDA-1113 is a digital audio DA that supports AES-3id 75 ohm digital audio standard and provides nine outputs. The input features clock regeneration for reduced jitter and signal restoration. An audio input signal status is also available indicating the input signal presence and validity with remote reporting.
Our Price: $149.95
Availability: Usually Ships in 5-14 Days
Add to Wish List
Henry Engineering MultiPort Multi-Format Audio Interface Panel
Henry Engineering
Item# MULTIPORT
MultiPort™ is a utility interconnect panel that facilitates interface between a studio and external audio equipment. MultiPort provides convenient access to a studio's analog and digital audio inputs and outputs, and allows connection to both professional and consumer gear. MultiPort's active circuitry performs all level,impedance, and topology conversion necessary for correct interface. MultiPort connects to any studio via its analog and digital inputs and outputs. The analog I/O interfaces...
Our Price: $650.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Henry Engineering USDA 2X4 Utility Summing & Distribution Amplifier
Henry Engineering
Item# USDA-2X4
USDA 2X4 is one of our most popular products because it has so many uses. It's a stereo distribution amplifier that can send audio to multiple places, or combine stereo to mono, or do both! Keep one handy for emergencies. U.S.D.A. (Utility Summing & Distribution Amplifier) is a unique 2x4 mini-DA that can be used to combine or split audio signals for distribution. It can be used as a 1x4 or 2x4 DA in stereo or mono. There are 2 inputs (1 stereo pair) and 4 outputs (2 stereo pairs). Front panel...
Our Price: $250.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Klark Teknik DN32-LIVE SD/SDHC and USB 2.0 Expansion Module for M32/X32 Mixers
Klark Teknik
Item# KT-DN32-LIVE
The Klark Teknik DN32-LIVE SD/SDHC and USB 2.0 Expansion Module for MIDAS M32 and BEHRINGER X32 mixers provides 32-channel bi-directional audio I/O via USB 2.0 for both live performance and studio recording, plus comprehensive remote operation of your DAW via HUI/Mackie Control emulation. The addition of dual SD/SDHC slots allows fully independent recording and playback of up to 32 channels of uncompressed WAV files in consistent sessions - up to the maximum capacity of the SD cards....
Our Price: $139.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Kramer AAD-OUT2-F16 2-Channel Analog & Digital Audio Output Card for VS-1616 Switcher
Kramer
Item# KR-AAD-OUT2-F16
The Kramer AAD-OUT2-F16 is a two-channel analog and digital output card for the VS-1616 Series Modular Multi-Format Digital Matrix Switchers. The AAD-OUT2-F16 outputs two analog and digital signals from the chassis. Features: Balanced Analog Audio over Terminal Block Connector. S/PDIF Digital Audio over RCA Connector. Specifications: Ports: 2 S/PDIF (digital audio) on RCA connectors, 2 balanced audio stereo (analog audio) on 5-pin terminal blocks Total Bandwidth: Analog...
Our Price: $544.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Marshall ARDM-AA-8XLR 8 Balanced Analog Audio Input (DB25) Module
Marshall Electronics
Item# MAR-ARDM-AA-8XLR
The Marshall ARDM-AA-8XLR is an optional module for the AR-DM Series rackmount digital audio monitors, which provides 8 balanced analog audio inputs with a DB-25 cable. Features: Nominal level: 0,+4,+6, or+8 dBu = -20dBFs Break-Out Cable included (DB-25 to XLR)
Our Price: $462.50
Availability: Usually Ships in 5-14 Days
Add to Wish List
Marshall ARDM-AES-4OUT 4 Unbalanced AES/EBU Output Module
Marshall Electronics
Item# ARDM-AES-4OUT
The Marshall ARDM-AES-4OUT is an optional module for the AR-DM Series rackmount digital audio monitors, which provides 4 unbalanced AES/EBU 75Ω BNC outputs, is capable of 4 AES/EBU outputs, it can De-embedded from HD-SDI or SD-SDI input, and is capable of 4 AES/EBU outputs decoded from Dolby® E/Dolby® Digital bitstream**. **Requires optional Dolby® E/Dolby® Digital Decoder Module (ARDM-D552)
Our Price: $462.50
Availability: Usually Ships in 5-14 Days
Add to Wish List
Midas DN4888 Bus-Powered StageCONNECT Interface with 8x8 Analog In/Out and Dual Ultranet Outputs
Midas
Item# MIDAS-DN4888
The Midas DN4888 is the perfect solution for connecting additional equipment to your monitor or FOH console. It provides 8 additional analog in and outputs to enable for 8 analog inserts or the connection to wireless devices, like 8 wireless microphones and 8 wireless in-ear systems. The StageConnect interface can be connected to other StageConnect devices using a single XLR cable for multi-channel audio transmission. There are various I/O options available providing easily...
Our Price: $339.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
MuxLab 500217 Audio Zone Amplifier 100W
MuxLab Inc
Item# MUX-500217
The MuxLab Audio Zone Amplifier 100W is a Class D amplifier which allows analog or digital sources to feed a pair of 50W per channel speakers. When set in Bridge mode and paired with the MuxLab 70V Transformer unit (500755-70V), the system is compatible with distributed 70V speaker systems over longer distances and supporting daisy chain configurations. The device may be controlled locally via pushbuttons and a knob, and remotely via RS232, IR and an IP webserver interface. The...
Our Price: $596.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
MuxLab 500219 Analog Audio Balun Amplifier
MuxLab Inc
Item# MUX-500219
The MuxLab Analog Audio Balun Amplifier allows one (1) analog source using the Muxlab Audio Balun (500028) or Muxlab Audio Matrix Switch (500210) to feed a 30W/channel stereo Class D amplifier using UTP Cat5e/6 cable. Applications: Audio Distribution Systems, Classroom training, Hospitality industry, Podium systems, Home theatre audio, Digital signage, Rental and staging, PA systems, Ceiling and shelf speakers. Features: RJ45 jack for input and binding posts for output 30W...
Our Price: $571.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Palmer Audio PMBLA Dual Channel Line Merger active
Palmer Audio
Item# PLM-PMBLA
The PMBL-ACTIVE is a 2-channel stereo line level merge box that can be used to merge two stereo line signals into one stereo output. One classic application: routing two mixing desks to one PA system. The unit has enough amplification to boost even semi-professional levels accordingly. The input channels are galvanically isolated from one another. Each channel offers a mute switch and the ability to mix the stereo signal down to mono. The unit is housed in a 1 U/9.5" case and has a built-in power...
Our Price: $559.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Palmer Audio SUPREME SOAKER Analog Dynamic Tube Amp Hub - 5 Inputs/6 Outputs
Palmer Audio
Item# PLM-PAL-PSUPOAK
The Palmer Supreme Soaker allows guitar players to maximize the potential of their tube amps in a way that has never been possible - until now. As a reactive attenuator and load box with a finely tuned analog speaker simulator built in, the Supreme Soaker allows guitarists to permanently dial in their amp's sweet spot - at any volume - and it will quickly become their go-to device in any musical situation, from playing and recording at home to rehearsing with a band, and even playing...
Our Price: $1,399.99
Availability: Usually Ships in 5-14 Days
Add to Wish List
Radio Design Labs RU-ADA4D 4 Channel Stereo Audio Distribution Amplifier
Radio Design Labs
Item# RDL-RU-ADA4D
The RU-ADA4D is a four channel stereo audio distribution amplifier with input and output gain adjustments and input level metering. The module may be operated in mono to provide up to eight distributed mono signals. The inputs and outputs are connected on rear-panel detachable terminal blocks. Each of the two line level inputs accepts either a balanced or an unbalanced signal. Each input is equipped with a front panel INPUT GAIN trimmer. Input signal levels between -14 dBV unbalanced and...
Our Price: $371.71
Availability: Usually Ships in 5-14 Days
Add to Wish List
Radio Design Labs RU-ADA8D 8 Channel Stereo Audio Distribution Amplifier
Radio Design Labs
Item# RDL-RU-ADA8D
The RU-ADA8D is an eight channel stereo audio distribution amplifier with input and output gain adjustments and input level metering. The module may be operated in mono to provide up to sixteen distributed mono signals. The inputs and outputs are connected on rear-panel detachable terminal blocks. Each of the two line level inputs accepts either a balanced or an unbalanced signal. Each input is equipped with a front panel INPUT GAIN trimmer. Input signal levels between -14 dBV unbalanced and...
Our Price: $557.29
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL AV-DC4 Line-Level Audio Divider/Combiner with Ground Lift
Radio Design Labs
Item# RDL-AV-DC4
The AV-DC4 is a mono transformer-coupled audio divider/ combiner module for use with balanced, low or high impedance audio inputs and outputs. Input and output connections are provided on XLR jacks with gold-plated contacts. The AV-DC4 features four identical channels. Each channel may be used as either an input or as an output. Two XLR jacks are provided on each channel. The female jack is used if the channel is being used as an input; the male jack is used if the channel is being used as an output....
Our Price: $317.78
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL EZ-ADA4 1x4 Stereo Audio Distribution Amplifier
Radio Design Labs
Item# EZ-ADA4
The EZ series offers unparalleled flexibility. Each unit is fully labeled on the front and rear for use either as a finished product or as a utility module. Installation of multiple products is quick and easy using the comprehensive range of EZ rack mounts, chassis, bezels, drawers and accessories. High quality full-size switches, long life controls, quality connectors, solid-state audio and video switching, gold plating and superior engineering combine to make EZ the best value in the industry....
Our Price: $199.77
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL HR-DDA4 Digital Audio Distributor - 1x4
Radio Design Labs
Item# HR-DDA4
The RDL HR-DDA4 is the ideal choice in installations requiring high quality distribution of a digital audio signal. The input and each of the four outputs support AES/EBU, S/PDIF or AES-3ID formats. The HR-DDA4 automatically detects a valid input on any of the four input jacks: S/PDIF optical, S/PDIF coaxial, AES-3ID or AES/EBU. The input is decoded, reclocked and retransmitted to four individually buffered outputs. Front-panel LEDs display the digital audio format and sample rate of a valid...
Our Price: $934.85
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL RU-MLD4 Microphone / Line Distribution Amplifier - 1x4
Radio Design Labs
Item# RU-MLD4
The RDL RU-MLD4 is a four channel audio distribution amplifier. The input and all four outputs may be connected through the front-panel XLR jacks or on the rear panel detachable terminal blocks. The input accepts either a balanced microphone or line level signal. Each of the four outputs provides either a microphone or line level signal. Both the front-panel XLR connectors and the rear-panel terminals are active at all times. The RU-MLD4 may be rack-mounted with the XLR jacks facing forward,...
Our Price: $385.88
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL RU-MLD4T Microphone / Line Distribution Amp - 1x4 with Transformer
Radio Design Labs
Item# RU-MLD4T
The RU-MLD4 is a four channel audio distribution amplifier. The input and all four outputs may be connected through the front-panel XLR jacks or on the rear panel detachable terminal blocks. The input accepts either a balanced microphone or line level signal. Each of the four outputs provides either a microphone or line level signal. Both the front-panel XLR connectors and the rear-panel terminals are active at all times. The RU-MLD4 may be rack-mounted with the XLR jacks facing forward, or may...
Our Price: $605.70
Availability: 2+ Weeks
Add to Wish List
RDL RU-TPS4A Active Sender / Distributor - Three Audio Inputs to Four Outputs
Radio Design Labs
Item# RDL-RU-TPS4A
The RU-TPS4A is a four output audio sender, signal and power distributor module compatible with RDL Format-A twisted pair products. Three line-level sources may be connected to the module using the +4 dBu balanced detachable terminal block. A bank of studio-quality buffer amplifiers feed the three pairs of the four rear-panel RJ45 OUTPUT jacks at the correct operating level. Three RDL Dual-LED VU meters are provided on the front panel of the RU-TPS4A. One meter monitors the audio level on each...
Our Price: $364.18
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL RU-UDA4 Stereo Audio Distribution Amplifier - 2x4 - RCA Jacks
Radio Design Labs
Item# RU-UDA4
The RU-UDA4 is the optimum choice where connectorized, unbalanced line-level distribution is needed. This unit features two separate, isolated channels. The RU-UDA4 may be used in stereo applications, or as two individual monaural distribution amplifiers. The input signals are buffered through output line drivers, providing four separate line-level unbalanced outputs for each of the two inputs. The RU-UDA4 performance is tailored around industry standard -10 dBV input/output levels. Excellent...
Our Price: $252.33
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL SF-BNC2 Bidirectional Unbalanced Stereo Audio Network Interface
Radio Design Labs
Item# RDL-SF-BNC2
The SF-BNC2 is a bidirectional Dante audio network interface. It features two unbalanced audio inputs (left and right) on RCA or stereo 3.5 mm Mini-jack connectors, as well as two unbalanced audio outputs (left and right) on RCA and stereo 3.5 mm Mini-jack connectors. Special software is not required to configure the SF-BNC2. Each input provides a network digital audio level of -20 dBFS for an unbalanced -10 dBV input. Each output provides -10 dBV unbalanced for a network digital...
Our Price: $723.31
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL SF-ND2 Two Dante Network Audio Channels to Stereo Digital Audio Output Interface
Radio Design Labs
Item# RDL-SF-ND2
The RDL SF-ND2 is a digital audio interface that converts two Dante network audio channels to a stereo digital audio output. The output is switch-selectable to provide an AES/EBU on XLR, or coaxial and optical S/PDIF. The switch enables the appropriate output jack and any required electrical and data format conversion. Special software is not required to configure the module. The SF-ND2 is a professional grade product for studio quality performance. The SF-ND2 is PoE powered....
Our Price: $506.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL SF-NL2 Two Dante Channel to Two Balanced Analog XLR Audio Network Interface
Radio Design Labs
Item# RDL-SF-NL2
The RDL SF-NL2 is a line-level interface that converts two Dante network audio channels to two balanced audio outputs on XLR connectors. Each channel provides +4 dBu balanced for a network digital audio level of -20 dBFS. Each output is equipped with a selector to set the output to line level or attenuate the output by 50 dB to mic level. Special software is not required to configure the module. The SF-NL2 is a professional grade product for studio quality fidelity and low noise...
Our Price: $440.02
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL SF-XMN4 Microphone To Network Interface
Radio Design Labs
Item# RDL-SF-XMN4
The SF-XMN4 is an interface that converts four XLR microphone inputs to Dante network audio channels. Special software is not required to configure the SF-XMN4. Each XLR input is equipped with a switch to set the gain for dynamic or condenser microphones. A dual-LED VU meter displays the level for each input to facilitate selection of the ideal gain range. P48 phantom voltage is supplied to each microphone input. The SF-XMN4 is a professional grade product with discrete mic preamplifiers...
Our Price: $961.84
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL STM-DA3 Microphone Level Distribution Amplifier - 1x3
Radio Design Labs
Item# STM-DA3
The STM-DA3 is designed for use in quality commercial sound, broadcast and recording applications. The 1.2 k Ohm balanced input accepts a wide variety of microphone input levels without loading professional low impedance microphones. A multi-turn trimmer is user adjustable for either gain or loss in order to match the facility standard microphone levels. Three balanced outputs provide nearly total isolation between the output lines. Unlike mic-splitting transformer systems, the STM-DA3 also provides...
Our Price: $200.86
Availability: Usually Ships in 5-14 Days
Add to Wish List
RDL TX-A2D Dual Audio Converter - Balanced to Unbalanced
Radio Design Labs
Item# RDL-TX-A2D
The RDL TX-A2D is the ideal choice in installations requiring passive isolation and level attenuation between a professional balanced line-level stereo source and consumer equipment unbalanced inputs. The TX-A2D is a complete unbalanced stereo line-level audio output module. The front panel provides a detachable terminal block for connecting each channel of a balanced +4 dBu audio source. The input signals are coupled to two front-panel gold plated phono jacks through studio-quality isolation...
Our Price: $155.38
Availability: Usually Ships in 5-14 Days
Add to Wish List
Remote Audio HotBox Version 2 1x6 Distribution Box
Remote Audio
Item# REM-HOTBOX-V2
The Hot Box v2 is the latest revision of Remote Audio's popular DC power distribution box, and the newest member of the MEON series of power management devices. Like its "Hot Box" predecessor, the Hot Box v2 features 6A self-resetting breakers on each of its XLR4F output connectors and a master on/off switch. Maximum current handling capability is 24A for the entire box. Hot Box v2 adds reverse-polarity protection and a much smaller physical footprint with all connectors entering and exiting...
Our Price: $271.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Rolls DA134 4 Channel RCA Distribution Amp
Rolls Corporation
Item# RLS-DA134
Designed for high end RCA audio distribution the Rolls DA134 is a four channel distribution amplifier. RCA and 1/8” inputs that can be switched from mono or stereo. The DA134 will distribute a mono signal to eight outputs, or a stereo signal to four stereo outputs. The outputs are designed to drive line level signals. The DA134 is the perfect distribution amp anywhere high quality sound distribution is required. Features: Expands the output of a stereo device to multiple outputs Can...
Our Price: $139.00
Availability: In Stock - Ships Factory Direct
Add to Wish List
Ross ADA-8402-A-R2AS AES / EBU openGear Reclocking Distribution Amplifier with Split Rear Module - 75 Ohm
Ross Video
Item# ADA-8402-A-R2AS
The Ross ADA-8402-B is an AES / EBU distribution amplifier designed for broadcast use. It provides 8 copies of the incoming balanced AES3 signal when used with the -R2B full rear module or 4 copies of the incoming signal when used with the -R2BS split rear module. The ADA-8402-B supports audio sampling frequencies from 32kHz to 96kHz. Cable equalization and reclocking techniques enable the ADA-8402-B to recover the incoming digital audio signal reliably. The ADA-8402-B also includes internal...
Our Price: $710.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Ross DAC-8418-A Dual AES to Quad Analog Audio Converter
Ross Video
Item# ROSS-DAC-8418-A
The Ross DAC-8418-A dual AES to quad analog audio converter is a broadcast quality modular product used to convert 2 unbalanced AES digital audio signals into 4 channels of analog audio. The DAC-8418-A supports audio sampling frequencies from 32kHz to 96kHz. The DAC-8418-A also has internal audio processing with independent channel gain, master stereo gain, sum (mono), and left or right only selection. It converts the 2 incoming AES / EBU digital audio signals to 2 stereo analog audio signals...
Our Price: $1,100.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Ross DAC-8418-A-R2A Dual AES to Quad Analog Audio openGear Converter with Rear Module
Ross Video
Item# ROSS-DAC8418AR2A
The Ross DAC-8418-A dual AES to quad analog audio converter is a broadcast quality modular product used to convert 2 unbalanced AES digital audio signals into 4 channels of analog audio. The DAC-8418-A supports audio sampling frequencies from 32kHz to 96kHz. The DAC-8418-A also has internal audio processing with independent channel gain, master stereo gain, sum (mono), and left or right only selection. It converts the 2 incoming AES / EBU digital audio signals to 2 stereo analog audio signals...
Our Price: $1,100.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Rupert Neve Designs RNDI-S Stereo Active Transformer DI
Rupert Neve Designs
Item# RUP-RNDI-S
The RNDI-S' signature sound is the product of custom Rupert Neve Designs transformers and class-A biased, discrete FET amplifiers. The carefully orchestrated union of these two elements is key to the unique response of the RNDI-S, delivering a powerful and vibrant direct sound capable of reproducing the full harmonic depth of basses, guitars, keyboards, acoustic instruments, professional line-level sources and consumer devices with a 3.5mm jack. With portable, powerful, larger-than-life tone,...
Our Price: $599.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Shure ANI4IN-BLOCK 4 Channel Dante Mic/Line Audio Network Interface-In with Block Connectivity
Shure Inc
Item# SH-ANI4IN-BLOCK
The Shure ANI4IN Audio Network Interface converts 4 analog audio channels into independent digital audio channels on a DanteTnetwork. Microphone, auxiliary, and line-level devices are supported, with adjustable gain and +48V phantom power for each channel. In networked conferencing systems, the Audio Network Interface provides a simple way to connect analog equipment onto the audio network, such as wireless microphones. The web application controls signal routing and channel settings from...
Our Price: $686.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex CM-CU21 Commentator Unit - 2 Commentators & 1 Guest
Sonifex
Item# SON-CM-CU21
The CM-CU21 is a high quality, portable Commentator Unit. Its sturdy construction and flexibility of features make it suitable for use in a wide variety of environments. It provides two fully featured commentator positions and a third guest position that can alternatively be used as a line-level input. Each position has an individual output, with two additional outputs providing a mix of all active commentary channels. A limit indicator on the main panel shows when the adjustable limiter on the...
Our Price: $4,855.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-AES4B3 Quad 3 Way Passive AES/EBU Distribution Amplifier with BNC Connectors
Sonifex
Item# SON-RB-AES4B3
The RB-AES4B3 is a passive, quad "one-to-three" splitter housed in a 19" rack. Each bank is designed to split a single AES-3id digital audio source to up to three destinations, using female BNC connectors. Particularly useful in a video production and broadcast environment, the RB-AES4B3 splits the input signal through high quality transformers. 75Ω termination can be applied, if desired, to unconnected outputs to maintain optimum carrier parameters. The RB-AES4B3...
Our Price: $1,157.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DA24MD 24 Way Mono Distribution Amplifier with Input Gain
Sonifex
Item# SON-RB-DA24MD
The RB-DA24MD is a 1U rack mount high performance 24 way audio distribution amplifier. It has 2 inputs which can be each individually routed to 12 outputs, or mixed and routed to all 24 outputs. The inputs can be configured as either dual mono, input 1 routed to outputs 1-12 and input 2 routed to outputs 13-24, or mixed-mono, inputs 1 and 2 mixed at a pre-set level and routed to all 24 outputs. When set to mixed-mono operation there are 3 different output mix level modes, enabled by altering internal...
Our Price: $967.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DAC1 Digital to Analog Audio Converter
Sonifex
Item# SON-RB-DAC1
Using 24 bit, 192kHz capable devices, the RB-DAC1 D/A Converter is a 1U rack-mount which produces a stereo balanced XLR or unbalanced phono output from an incoming AES/EBU or S/PDIF digital input signal. There is also a headphone output with volume control for monitoring purposes. The analogue outputs have an output level control, allowing full-scale settings selectable from +12dBu, +18dBu or +24dBu. The RCA phono outputs have a further 8.5dBu attenuation incorporated. There is...
Our Price: $1,174.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DDA22 Digital Audio Distribution Amplifier With Multiple Outputs
Sonifex
Item# SON-RB-DDA22
The RB-DDA22 is a multiple input and multiple output digital audio distribution amplifier designed to accept one of 5 different digital inputs and output to 22 digital audio outputs of 5 different connector types. It is used for distributing digital audio data in many formats, repeating both the audio data and the status information of the input whilst re-clocking the data and re-normalising to the appropriate standard digital audio levels. Input Signals: 1 x XLR 3 female AES/EBU digital audio...
Our Price: $1,440.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DDA6A 6 Way Stereo AES/EBU Digital Distribution Amplifier
Sonifex
Item# SON-RB-DDA6A
The RB-DDA6A digital distribution amplifier is used for distributing digital audio data in AES/EBU format, repeating both the audio data and the status information of the input whilst re-normalising to standard digital audio levels.It has a single XLR-3 female AES/EBU audio input which is distributed to 6 XLR-3 male AES/EBU outputs. Applications include distributing audio from a digital mixing desk to multiple digital recorders, or feeding multiple studios with an output from a DAT machine. It...
Our Price: $977.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DDA6A-2P 6 Way Stereo AES/EBU Digital Distribution Amplifier
Sonifex
Item# SON-RB-DDA6A-2P
The RB-DDA6A-2P digital distribution amplifier is used for distributing digital audio data in AES/EBU format, repeating both the audio data and the status information of the input whilst re-normalising to standard digital audio levels. It has a single XLR-3 female AES/EBU audio input which is distributed to 6 XLR-3 male AES/EBU outputs. Applications include distributing audio from a digital mixing desk to multiple digital recorders, or feeding multiple studios with an output from a DAT machine. It...
Our Price: $1,183.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DDA6W 6 Way Word Clock Distribution Amplifier
Sonifex
Item# SON-RB-DDA6W
The RB-DDA6W word clock distribution amplifier distributes a word clock BNC input signal to 6 word clock BNC outputs re-conditioned. It is used to distribute reference clocks for digital audio systems. It has a single female BNC audio input which is distributed to 6 female BNC outputs. The units primary application is to distribute a master TTL word clock source to multiple pieces of equipment that need to be synchronised from the master. Features: Specifications: Input impedance:...
Our Price: $960.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-DDA6W-2P 6 Way Word Clock Distribution Amplifier with Dual Power Supplies
Sonifex
Item# SON-RB-DDA6W-2P
The RB-DDA6W-2P 6 Way Word Clock Distribution Amplifier distributes a word clock BNC input signal to 6 word clock BNC outputs re-conditioned. It is used to distribute reference clocks for digital audio systems. It has a single female BNC audio input which is distributed to 6 female BNC outputs. The units primary application is to distribute a master TTL word clock source to multiple pieces of equipment that need to be synchronised from the master. The unit provides redundancy...
Our Price: $1,166.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-MM1 Mix-Minus Generator
Sonifex
Item# SON-RBMM1
Whenever programming originates from outside of the studio, or if listeners/viewers are calling up a phone-in using telephone hybrids or codecs, mix-minus feeds are required. Most telephone lines incur delays which prohibit off-air monitoring, because the caller, or remote talent, would hear their own voice in delay which is very disconcerting. The solution is to feed a mix back to the caller minus his or her own voice. Some mixing desks do not have a dedicated telco channel to generate a clean-feed,...
Our Price: $692.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-PA2 Dual Stereo RIAA Phono Amplifier
Sonifex
Item# SON-RB-PA2
The Sonifex RB-PA2 is a dual stereo RIAA equalised phono amplifier. This record player preamp amplifies the small signal from your pick up cartridge (either moving magnet or high output moving coil magnetic) and provides the necessary RIAA equalisation required for vinyl records, to match it to a line input of your mixer, or amplifier. It uses a clean RIAA response making it ideal for use with broadcast turntables and DJ decks and where vinyl records are being archived to CD for high quality...
Our Price: $642.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Sonifex RB-SC2 Dual Sample Rate Converter
Sonifex
Item# SON-RBSC2
The RB-SC2 sample rate converter is a 1U rack-mount which produces AES/EBU, S/PDIF and TOSlink optical level digital audio outputs from a balanced AES/EBU, S/PDIF and TOSlink optical level digital audio inputs. The sample rate of the outputs can be set by an internal clock or from various external synchronize sources. Features: It supports higher sample frequency rates up to and including 176.4kHz and 192kHz. It has 2 independent sample rate converter circuits that use a common clock source to...
Our Price: $1,594.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Studio Technologies Model 42A 1RU Interface for Broadcast-Standard IFB Outputs from Line-Level Audio Sources
Studio Technologies Inc.
Item# MODEL-42A
The Studio Technologies Model 42A is designed to create broadcast-standard IFB outputs from line-level audio sources. The unit's primary application is to interface analog outputs associated with digital matrix intercom systems with broadcast IFB user devices. The Model 42A creates four independent IFB outputs. For convenience, the four outputs can be connected by way of eight 3-pin male XLR connectors; four of which are located on the back panel and four on the front. Installation...
Our Price: $1,250.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
Symetrix 80-0090 xOUT 12 xIO Audio Expanders 1RU 12x0 Dante I/O Endpoint - 12 Line Out
Symetrix
Item# SYX-80-0090
Easily expand your Radius NX, Edge or Prism Dante DSPs system with Syemtrix xIO Audio Expanders. Designed for use with Symetrix Dante-enabled DSPs Software setup using Composer Low-cost way to increase system analog I/O capacity Ultra low latency - no audible delays Top of the line specifications Features: 12 channel Dante receive. Dante protocol over standard IT networks with ultra-low latency. 12 line outputs, with industry leading performance specifications. Composer software...
Availability: Usually Ships in 5-14 Days
Item Details
Symetrix 80-0112 xOUT xIO Audio Expanders with Dante - 4 LIne Out - 4x0 Dante - PoE - 1/2 Rack
Symetrix
Item# SYX-80-0112
Easily expand your Radius NX, Edge or Prism Dante DSPs system with Symetrix xIO Audio Expanders. Designed for use with Symetrix Dante-enabled DSPs Software setup using Composer Low-cost way to increase system analog I/O capacity Ultra low latency - no audible delays Top of the line specifications Features: 1/2 Rack Form Factor PoE - Injectors included 4 analog outputs Optional rack and surface mounting kits sold separately Specifications: Analog Output Frequency Response:...
Availability: Usually Ships in 5-14 Days
Item Details
Symetrix xIO 4X4 Dante xIO Audio Expanders w/ Dante- 4 Mic/LIne In - 4 LIne Out - 4x4 Dante - PoE - 1/2 Rack
Symetrix
Item# SYX-80-0106
Easily expand your Radius NX, Edge or Prism Dante DSPs system with Symetrix xIO Audio Expanders. Designed for use with Symetrix Dante-enabled DSPs Software setup using Composer Low-cost way to increase system analog I/O capacity Ultra low latency - no audible delays Top of the line specifications Features: 1/2 Rack Form Factor PoE - Injectors included 4 analog mic/line inputs + 4 analog outputs Optional rack and surface mounting kits sold separately Specifications: Analog...
Availability: Usually Ships in 5-14 Days
Item Details
TOA T-001T Dual Line Output Expansion Module with DSP
TOA Electronics, Inc.
Item# TOA-T-001T
The T-001T is a plug-in module designed for use with the 9000 Series amplifiers and can provide two independent balanced outputs. It can drive load of 600 O up to +16 dB. It can process effect for TONE/EQ/COMPRESSOR to two outputs independently.
Our Price: $184.00
Availability: Usually Ships in 5-14 Days
Add to Wish List
TOA T-01S Balanced Line Output Module 600ohm
TOA Electronics, Inc.
Item# TOA-T01S
For transformer-isolated output of mixing bus signal to feed other mixers, amps and tape recorders. (Functions only in A-900MK2, M-900MK2, W-900A Series, 700 Series and BG-M Series; not usable in P900MK2 Series). Features: Controls/Functions: Gain Control Gain (Adjustable): 4 ~ 20 dB Max Imput/Output: +18 dB tb Signal to Noise (S/N): 80 dBu (S/N) Physical Connector: Removable Terminal Block
Our Price: $140.00
Availability: 2+ Weeks
Add to Wish List
US Audio DA-2 Distribution Amp
Whirlwind
Item# DA-2
In normal (stereo) mode, the Whirlwind/US Audio DA-2 provides four outputs per each of two inputs. A front panel COMBINE switch applies both inputs to all 8 outputs, where the DA-2 becomes a one or two in, eight out DA. Each output is ground lifted and has its own level control and clip indicator light. Input signals are monitored by signal-present LEDs and clip LEDs. The headphone circuit can be switched to monitor either channel. All audio connections are made through actively balanced...
Our Price: $846.00
Special Price: $798.00
Availability: Usually Ships in 5-14 Days
Add to Wish List

In electronics, audio distribution amplifiers, or simply distribution amp or DA, is a device that accepts a single audio input signal and provides this same signal to multiple isolated outputs. Why is this important ? Because audio distribution amplifiers allow the signal to be distributed to multiple destinations without ground loops or signal degradation. Impressed? And if that isn't enough they are also used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation. Audio distribution amplifiers from Markertek will get your message out there!

Sign In

Audio Distribution Amplifiers

Narrow Products

By Brand

By Price Range

Filter By