-
Item# RNE-DANTEX
The Rane DANTEx is an optional plug-in card for the Rane Terminal 1010x that allows system designers to integrate a Terminal 1010x processor with Dante-equipped microphones, amplifiers, breakout boxes, mixing consoles and other supported devices. It provides 32 inputs and 32 outputs of Dante digital audio with supported samples rates of 44.1kHz, 48kHz, 88.2kHz and 96kHz. Built-in sample rate conversion (SRC) converts the Dante sample rate to the fixed 48kHz sample rate required by the Terminal...

-
Item# RNE-DR6
The DR6 is a fully customizable touchscreen remote for the HAL family. It supports multiple pages or tabs and any set of levels, toggles, selectors and/or commands. Drag, drop and resize controls any way that's desired. Use custom background images and logos in full-color on the 7-inch LCD display.
Screw the included wall-mount bracket over U.S. or international electrical boxes, or flush mount the 3/4" thick DR6 with a 2-inch (5 cm) square hole in the wall to accommodate the cable.
The...

-
Item# RNE-DRZH
The Rane DRZH is a wall-mounted digital remote (DR) for use with all Rane multiprocessors, including the new Zonetech audio processor. The DRZH features source selection and level control through the use of a single knob. It has a sleek black glass design, and the OLED display is easy to read in any environment. Connect the DRZH to RANE DSP with a Cat5e (or better) cable for a local run up to 1000 ft (300m) away from the equipment rack.
Each DRZH may be installed onto a standard U.S. 1-gang...

-
Item# RNE-RAD16Z
The RAD16z provides an alternative to standard switchboxes for areas in which a switchbox is impractical, such as in stage floor pockets or above ceilings. Its form factor is a rugged metal box with flexible surface mounting options. The RAD16z is plenumrated UL 2043.
It contains 2 balanced Mic / Line / Line-Plus inputs and 2 balanced line outputs on Euroblock connectors. Line-Plus allows a stereo unbalanced source to connect to a single balanced input and be mono'ed. Inputs are individually...

-
Item# RNE-RAD22
The Rane RAD22 adds flexible I/O capability to RANE DSP systems. It provides two mic and two line inputs via XLR/TRS combination jacks and an 1/8" (3.5mm) stereo line output for monitoring, recording or amplification. Smart muting allows for the disconnecting of XLR and 1/4" cables to prevent disruption to sound systems for hot-swapping of microphones - even with 24V phantom power applied. Connect the RAD22 to RANE DSP with a Cat5e (or better) cable for a local run up to 500 feet (150m) away...

Our Price: $349.00
Availability: Direct Ship from manufacturer, contact us for availability
Add to Wish List
-
Item# RNE-RAD26
The Rane RAD26 provides any room with end user control via the color LCD display and rotary encoders. It also features a dual universal audio I/O interface, line-level input jacks for local needs, a headphone output, and a dual 4-watt amp all using using one shielded cat5e (or better) cable drop. Three logic closure inputs and three active-low outputs add to the control capabilities. The built-in amplifier powers a small stereo pair of room speakers, or it can be switched in software to power...

-
Item# RNE-RPI
The Rane RPI is a remote powering device for the DR6 Touchscreen Digital Remote and the RAD26 One-Room Remote Audio Device. This power supply is needed when using the DR6 or RAD26 with rackmount HAL units (HAL3s and legacy units). The RPI is connected between the HAL and the peripheral controller using shielded Cat5e cable (or better), and can be located at any point between the HAL units and the peripherals within a 325ft (100m) maximum distance. It requires 100-240 VAC and utilizes...

Our Price: $99.00
Availability: Direct Ship from manufacturer, contact us for availability
Add to Wish List
-
Item# RNE-TERMINAL1010
The Rane Terminal 1010x takes the DSP Experience to the next level with an intuitive front-panel that enables users to control 10 analog balanced inputs for Mic/Line/+48V and 10 balanced outputs. There are also 6 flexible RAD Plus PoE ports to connect breakout boxes and wall plate remote controls and 4 Universal GPIO logic ports for external devices such as alarm systems, sensors, lights, projectors, etc. There is also a slot for an optional DANTE™ 32x32 card for network connectivity.
...

-
Item# RNE-ZONE-PAGER
The RANE Zone Pager is a paging station that allows users to page up to (6) zones separately, to (2) groups of zones, and to all zones at the same time. Lights will indicate if the zone is READY or BUSY (already being paged by a higher-priority paging station) and when the chime has completed (if enabled).
The Zone Pager accepts an included dynamic gooseneck microphone via a 3-pin XLR connector. The microphone input supplies 24V phantom power for condenser microphones. The Zone Pager is...

-
Item# RNE-ZONETECH
The Rane Zonetech features six inputs and six outputs for multi-zone audio distribution and control. Powered by exclusive Rane Halogen Lite software, it requires no programming, so operation is quick and intuitive.
An additional wireless input for Bluetoothr 4.1 AD2P is provided to receive streaming audio from a smartphone or tablet. A contact closure for emergency "Mute All" is provided for integration with alarm systems. All zones have balanced outputs and the 6th zone can work in Stereo...
